Filter
Top Products
14
The “LFO1 Intensity,” “JS+Y (LFO1 JS+Y Int.)” and “AMS
(LFO1 AMS)” settings will be added to determine the depth
and direction of the pitch modulation applied by OSC1
LFO1 (☞p.244).
LFO2:
LFO2 Intensity [–12.00…+12.00]
JS+Y Int. (LFO2 JS+Y Int.) [–12.00…+12.00]
AMS (LFO2 AMS) [Off, (PEG, FEG, AEG, KT, EXT)]
Intensity (AMS Intensity) [–12.00…+12.00]
Refer to the above “LFO1.”
▼ 2–1: Page Menu Command
☞0–1A: Write Program, 1–1A: Copy Oscillator, 1–1B: Swap
Oscillator
2–2: OSC2 P.Mod (OSC2 Pitch Mod.)
These settings specify how key position (note number) will
affect the pitch, and select the controllers that will affect the
oscillator 2 pitch and specify the depth of control. They also
specify the depth at which the pitch EG will affect the pitch of
oscillator 2, and the depth of pitch change produced by LFO1
and LFO2. Portamento on/off settings etc. are also found
here.
For details on the functions of these parameters, refer to the
preceding section “2–1: OSC1 P.Mod (OSC1 Pitch Mod.).”
2–3: Pitch EG
Here you can make settings for the pitch EG, which creates
time-variant changes in the pitch of oscillators 1 and 2.
The depth of pitch change produced by these EG settings on
oscillator 1 (2) is adjusted by “Pitch EG” (2–1b, 2–2).
2–3a: Pitch EG
These settings specify how the pitch will change over time.
Level:
These parameters specify the amount of pitch change.
The actual amount of pitch change will depend on the
“Pitch EG” (2–1b, 2–2) parameter “Intensity.” For example
with an “Intensity” setting of +12.00, a “Level” setting of
+99 would raise the pitch one octave, and a “Level” setting
of –99 would lower the pitch one octave.
Start (Start Level) [–99…+99]
Specifies the amount of pitch change at note-on.
Attack (Attack Level) [–99…+99]
Specifies the amount of pitch change when the attack time
has elapsed.
Release (Release Level) [–99…+99]
Specifies the amount of pitch change when the release time
has elapsed.
Time:
These parameters specify the amount of time over which the
pitch change will occur.
Attack (Attack Time) [0…99]
Specifies the time over which the pitch will change from
note-on until it reaches the pitch specified as the attack level.
Decay (Decay Time) [0…99]
Specifies the time over which the pitch will change after
reaching the attack level until it reaches the normal pitch.
Release (Release Time) [0…99]
Specifies the time over which the pitch will change from note-
off until it reaches the pitch specified as the release level.
2–3b: Level Modulation
These settings allow the pitch EG Level parameters to be con-
trolled by alternate modulation.
AMS1 (Level Mod. AMS1) [Off, (KT, EXT)]
Selects the source that will control the pitch EG Level param-
eters (“AMS List” ☞p.242).
Intensity (AMS1 Intensity) [–99…+99]
Specifies the depth and direction of the effect applied by
“AMS1 (Level Mod. AMS1).”
With a setting of 0, the levels specified by “Pitch EG” (2–3a)
will be used.
For example if “AMS1 (Level Mod. AMS1)” is SW1:CC#80,
pressing the [SW1] key to turn it on will change the Level
parameters of the Pitch EG. (Set “Panel Switch Assign” (1–
4a) to SW1 Mod.CC#80.) As the absolute value of “Intensity
(AMS1 Intensity)” is increased, the pitch EG levels will
change more greatly when the [SW1] key is turned on. The
direction of the change is specified by “St (AMS1 SW Start)”
and “At (AMS1 SW Attack).” When the [SW1] key is turned
off, the pitch EG levels will return to their own settings.
If “AMS1 (Level Mod. AMS1)” is set to Velocity, increasing
the absolute value of “Intensity (AMS1 Intensity)” will pro-
duce increasingly wider change in pitch EG levels for
strongly-played notes. The direction of the change is speci-
fied by “St (AMS1 SW Start)” and “At (AMS1 SW Attack).”
As you play more softly, the pitch change will draw closer to
the pitch EG levels.
2–3
2–3a
2–3c
2–3b
Note-on
Note-off
Attack
Time
Decay
Time
Start Level
Release Level
Release Time
Attack Level
+99 = approximately 1 octave
–99 = approximately 1 octave
0 = pitch when
key is held
(sustained)
Time
Time-varying pitch settings (when Pitch EG Intensity = +12.00)