Filter
Top Products
153
Global
P0
P1 P2 P3 P4 P5 P6
Example)
We will use a “Arpeggio Tone Mode” Fixed Note pattern
on drums. Tone 1 is assigned a note number that will
sound a kick, Tone 2 a snare, and Tone 3 a hi-hat.
With a setting of Trigger As Played, pressing one key
will sound only Tone 1 (kick). Pressing two keys will
sound Tone 1 (kick) and Tone 2 (snare). Pressing three
keys will sound all three Tones 1–3 (kick, snare, hi-hat). If
the “Velocity” of each Tone is set to Key, each Tone will
be sounded at the velocity with which each key was
played.
With a setting of Trigger All Tones, playing one key is
sufficient to sound all three; Tone 1 (kick), Tone 2 (snare),
and Tone 3 (hi-hat). If the “Velocity” of each Tone is set
to Key, the Tones will be sounded at the corresponding
velocity each time a key is pressed.
▼ 6–1: Page Menu Command
6–1A: Write Arpeggio Patterns
This command writes user arpeggio patterns U000 (I-A/B)–
U506 (User).
1 Select “Write Arpeggio Patterns” to access the dialog
box.
2 To execute the Write command press the OK button. To
cancel without executing press the Cancel button.
You can also press the SEQUENCER [REC/WRITE] key
to write arpeggio patterns in the same way as the “Write
Arpeggio Patterns” command. Press the SEQUENCER
[REC/WRITE] key to access the dialog box, and write the
data.
“Pattern,”“ (Tempo),” “Octave,” “Resolution,” “Sort,”
“Latch,” “Key Sync,” and “Keyboard” are parameters
that are set in Program, Combination, Song, and Song
Play modes. The Write operation executed here does
not save these parameters.
If you move here from Program or Combination mode
and set these parameters, you must return to the origi-
nal mode and write them.
6–1B: Rename Arpeggio Pattern
This command renames the selected user arpeggio pattern.
Up to sixteen characters can be used. (☞BG p.57)
Preset patterns P000–P004 cannot be renamed.
6–1C: Copy Arpeggio Pattern
This command copies the settings of another user arpeggio
pattern to the currently selected arpeggio pattern.
It is not possible to copy from a preset arpeggio pattern
P000–P004.
1 Select “Copy Arpeggio Pattern” to access the dialog box.
2 Select the copy source arpeggio pattern “From.”
3 To execute the Copy Arpeggio Pattern command press
the OK button. To cancel without executing press the
Cancel button.
Be aware that when you execute “Copy Arpeggio Pat-
tern,” all settings of the currently selected arpeggio pat-
tern will be overwritten.
6–2: Pattern Edit
Here you can input Tones 0–11 for each step 01 to 48. “Step”
can be a maximum of 48 steps, and Tone corresponds to up
to twelve notes for the (up to) twelve keys pressed simulta-
neously. If “Sort” (6–1a) is checked, the notes that were
pressed will correspond in ascending order of pitch to Tones
0, 1, etc. If “Sort” (6–1a) is unchecked, the notes that were
pressed will correspond to Tones 0, 1, etc. in the order in
which they were pressed.
These parameters are not valid for preset patterns
P000–P004.
6–2a: Step No., Pitch Offset, Gate, Velocity, Flam,
Tone No., Fixed Note No.
Step No. (Step Number) [01...48]
Selects the step that you wish to edit, and set/reset each
Tone. When the “Step No” is selected, use the numeric keys
to input the Tones. Numeric keys [0]–[9] correspond to
Tones 0–9, [–] corresponds to Tone 10, and [./10’s HOLD] to
Tone 11. Each time you press a key, the Tone will be set or
reset.
When “Arpeggio Tone Mode” (6–1b) is Normal, the display
will indicate “●.” When set to Fixed Note, the display will
indicate “❍.”
If you wish to delete all Tones of a step, use the “Delete”
page menu command. To insert a blank step, use the
“Insert” page menu command.
Pitch Offset [–48...+48]
For each step, the pitch corresponding to the Tone can be
raised or lowered in semitone steps. This lets you make set-
tings for the same tone in each step to create a melody, or to
make settings for two or more tones in each step to play par-
allel chords.
Gate [Off, 001...100%, Legato]
Off: That step will not sound even if Tones have been speci-
fied.
Legato: Notes will continue sounding until the same Tone is
sounded next, or until the pattern returns to the beginning.
At this time, the display will change to “” or “■.”
This setting is valid when the Program, Combination, Song,
or Song Play mode parameter “Gate” (Program P7: 7–1a,
Combination P7: 7–2a/3a, Sequencer/Song Play P7: 7–3a/
4a) is set to Step. When making this setting, make sure that
“Gate” is set to Step in the mode from which you arrived
here.
6–1A
6–1B
6–1C
6–2
6–2a