Filter
Top Products
202
“AUTOFADE Src”=Gate1, “LFO Frequency [Hz]”=1.0
“LFO Frequency Mod”=AUTOFADE, “Amt”=3.0
The effect is off when a value for the dynamic modulation
source specified for the “AUTOFADE Src” parameter is
smaller than 64, and the effect is on when the value is 64 or
higher. The AutoFade function is triggered when the value
changes from 63 or smaller to 64 or higher.
028: St. Auto Fade Mod.
(Stereo Auto Fade Modulation)
This stereo chorus/flanger effect enables you to control the
LFO speed and effect balance using auto fade, and you can
spread the sound by offsetting the phase of the left and right
LFOs from each other.
029: 2Voice Resonator
This effect resonates the input signal at a specified pitch. You
can set the pitch, output level, and pan settings for two reso-
nators individually. You can control the resonance intensity
via an LFO.
a
AUTOFADE Src Off...Tempo
Selects the modulation source that starts AutoFade
☞ Fx:027,
Rate
Sets the rate of fade-in
1...100
☞ Fx:027
Fade-In Dly (Fade-In Delay) [msec]
Sets the fade-in delay time
00...2000msec
☞ Fx:027
b
LFO Waveform
Selects LFO Waveform
Triangle, Sine
LFO Shape –100...+100
Determines how much the LFO waveform is changed
☞ Fx:020
c
LFO Phase [degree] –180...+180
Sets the LFO phase difference between the left and right
☞ Fx:010
d
LFO Frequency Mod D-mod, AUTOFADE
Switches between D-mod and AUTOFADE for the LFO frequency
modulation
☞ Fx:027
e
LFO Frequency [Hz]
Sets the LFO speed
0.02...20.00Hz
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
f
L Delay Time [msec]
Sets the left channel delay time
0.0...500.0msec
R Delay Time [msec]
Sets the right channel delay time
0.0...500.0msec
g
Depth
Sets the depth of LFO modulation
0...200
AUTOFADE
AutoFade
Note On
All Note Off
Fade-In Rate
AUTOFADE Src=Gate1
LFO Frequency[Hz]=1.0
LFO Freq. Mod=AUTOFADE
Amt=+3.0
LFO Frequency
=1.0+3.0=4.0Hz
LFO Frequency
=1.0Hz
Gate1 Signal
AUTOFADE
Fade-In Dealy
AutoFade
LFO Frequency
Wet / Dry
Delay
Delay
Left
Right
Feedback
LFO Shape
LFO Phase
LFO: Tri / Sine
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
h
Feedback
Sets the feedback amount
–100...+100
☞ Fx:020
High Damp [%] 0...100%
Sets the feedback damping amount in the high range
☞ Fx:020
i
Wet/Dry Mod D-mod, AUTOFADE
Switches between D-mod and AUTOFADE for the effect balance
modulation
☞ Fx:027
j
Wet/Dry –Wet...–1:99, Dry, 1:99...Wet
Sets the balance between the effect and dry sounds
☞ Fx:010, 020,
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
–100...+100
a
Control Mode Manual, LFO, D-mod
Switches the controls of resonance intensity
☞,
LFO/D-mod Invert Off, On
Reverses the Voice 1 and 2 control when LFO/D-mod is selected
☞
b
LFO Frequency [Hz]
Sets the LFO speed
0.02...20.00Hz
D-mod Src Off...Tempo
Selects the modulation source that controls resonance intensity
c
Mod. Depth –100...+100
Sets the amount of resonance intensity control via LFO/D-mod
Tr im
Sets the input level at the resonator
0...100
d
Voice1: Pitch
Sets the voice1 Pitch for resonance
C0...B8
Fine [cent] –50...+50
Fine-adjusts the voice 1 pitch for resonance
e
Voice1: Resonance –100...+100
Sets the intensity of resonance when Control Mode = Manual
☞
High Damp [%] 0...100%
Sets the damping amount of resonant sound in the high range
☞
f
Voice1: Level
Sets the Voice1 output level
0...100
Pan
Sets the Voice1 stereo image
L6...R6
g
Voice2: Pitch
Sets the Voice2 Pitch for resonance
C0...B8
Fine [cent]
Fine-adjusts the voice 2 pitch for resonance
–50...+50
h
Voice2: Resonance –100...+100
Sets the intensity of resonance when Control Mode = Manual
☞
High Damp [%] 0...100%
Sets the damping amount of resonant sound in the high range
☞
Left
Right
Resonance
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
High Damp
High Damp
Trim
Trim
+
Level
Level
Pan
Pan
Control Mode
D
-mod
LFO
Manual
Invert: On/Off
Resonator
Resonator
Pitch, Fine [cent]