Filter
Top Products
173
0-10-20-30-40-50-6
Disk
If you select a 44.1 kHz or 48 kHz WAVE file, you can
press the SAMPLING [START/STOP] key to play it
back. In this case, the lower line will indicate “(Sam-
pling START/STOP plays selected file).”
If you press the Exit button, the dialog box will close, and no
further WAVE files will be added.
You can continue adding as many WAVE files as desired
until you press the Exit button.
Cut
Deletes the audio track.
When you place the cursor at “WAVE File” of the audio
track that you want to delete, and press the Cut button, that
audio track will be deleted. Any subsequent audio tracks
will be moved forward.
Clear
Erases the audio track list.
If you want to keep an audio track list, use “Save Audio
CD Track List” (0–2I) to save it on floppy disk or other
medium.
0–4d: Drive select
Drive select [ID0...6, CDD: Name]
Selects the CD-R/RW drive that contains the media that you
will use to create an audio CD. (☞0–1c)
Drives other than a CD-R/RW drive cannot be selected
here.
▼ 0–4: Page Menu Command
0–4A: Swap Track
This command exchanges (swaps) the order of two audio
tracks.
1 Select “Swap Track” to access the dialog box.
2 Use “Source1” and “Source2” to select the two audio
tracks that you want to exchange.
3 Press the OK button to execute the Swap Track opera-
tion, or press the Cancel button to cancel without execut-
ing.
0–4B: Write to CD
When this command is executed, the WAVE files specified in
the audio track list will be written as audio CD tracks. If
desired, you can also finalize the disc (☞p.172) at this time.
To avoid errors, do not subject the TRITON STUDIO to
vibration or physical shock while data is being written
to the CDRW-1 option (if installed), or while formatting
is taking place.
1 Create an audio track list, use “Drive select” to select the
CD-R/RW drive, and make sure that CD-R/RW media is
inserted in the drive.
2 Select “Write to CD” to access the dialog box.
3 Use “Speed” to specify the writing speed. The writing
speeds supported by your CD-R/RW drive will be dis-
played.
Be aware that if your system has a slower data transfer
rate, using an excessively fast writing speed will pro-
duce writing errors. Depending on the drive you are
using, problems with the speed may make it impossible
to write, but you can perform a test beforehand to iden-
tify such problems. It is a good idea to perform a test
write when you write for the first time, to verify the
speed limitations of your drive.
Use “Mode” to specify the writing method.
Test: Tests whether the data can be written correctly. Data
will not actually be written to the CD-R/RW media, but
all other processing will occur just as if data were actu-
ally being written. Use this when you want to check
whether writing can be performed correctly. If an error
occurs, the display will indicate “Error in writing to
medium.”
Test and Write: A test write will be performed, and if the
test is successful, the disc will actually be written. We rec-
ommend that you use this method for fast writing
speeds.
Write: The disk will only be written.
4 Specify whether the CD-R/RW media will be finalized
after the audio tracks have been written to it.
If “Execute finalize too” is checked, the disc will be final-
ized.
If this is not checked, the disc will not be finalized.
If you want only to finalize the disc, use “Finalize
Audio CD” (0–4C).
5 Press the OK button to execute writing or test writing to
the CD-R/RW media, or press the Cancel button to can-
cel without executing.
WAVE files with a 48 kHz sampling frequency will be
converted to 44.1 kHz when they are written.
In order for this processing to be performed, free space
of approximately the same size as the WAVE file to be
converted will be required on the drive that contains
the WAVE file. Before executing, please make sure that
the drive containing the WAVE file has enough free
space.
If the track is shorter than 4 seconds, silence will be
automatically added to increase the length to 4 seconds.
Two seconds of silence will be added to the end of each
track except the last track.
0–4C: Finalize Audio CD
This command finalizes CD-R/RW media to which audio
tracks have already been written.
To avoid errors, do not subject the TRITON STUDIO to
vibration or physical shock while data is being written
to the CDRW-1 option (if installed), or while formatting
is taking place.
1 Use “Drive select” to select the drive, and make sure that
the drive contains valid media.
0–4A
0–4B
0–4C
0–4D