Filter
Top Products
Effect
195
014: Stereo Decimator
This effect creates a rough sound like a cheap sampler by low-
ering the sampling frequency and data bit length. You can
also simulate noise unique to a sampler (aliasing).
a: Pre LPF
If a sampler with a very low sampling frequency receives very
high-pitched sound that could not be heard during playback, it
could generate pitch noise that is unrelated to the original sound.
Set “Pre LPF” to ON to prevent this noise from being generated.
If you set the “Sampling Freq” to about 3kHz and set “Pre LPF” to
OFF, you can create a sound like a ring modulator.
e: Resolution, f: Output Level
If you set a smaller value for the “Resolution” parameter, the
sound may be distorted. The volume level may also be changed.
Use “Output Level” to adjust the level.
015: St. Analog Record
(Stereo Analog Record)
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the modulation
caused by a warped turntable.
b: Flutter
This parameter enables you to set the depth of the modulation
caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click noise that
occurs once every rotation of the turntable. This simulation repro-
duces record noise, and the noise generated after the music on a
vinyl record finishes.
a
Pre LPF Off, On
Selects whether the harmonic noise caused by a decrease in sam-
pling frequency is generated or not
☞
High Damp [%]
Sets the ratio of cut of the high range
0...100%
b
Sampling Freq (Sampling Frequency) [Hz]
Sets the sampling frequency
1.00k...48.00kHz
Src Off...Tempo
Selects the modulation source of the sampling frequency
Amt –48.00k...+48.00kHz
Sets the modulation amount of the sampling frequency
c
LFO Frequency [Hz]
Sets the LFO speed
0.02...20.00Hz
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
Depth 0...100
Sets the depth of the sampling frequency LFO modulation
Src Off...Tempo
Selects the LFO modulation source of the sampling frequency
Amt –100...+100
Sets the LFO modulation amount of the sampling frequency
e
Resolution
Sets the data bit length
4...24
☞
f
Output Level
Sets the output level
0...100
☞,
Src
Selects the modulation source for the output
level
Off...Tempo
Amt
Sets the modulation amount of the output level
–100...+100
g
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Pre LPF
Pre LPF
High Damp Output Level
High Damp Output Level
Sampling Frequency
Decimator
Decimator
D
-mod
LFO
Resolution
Resolution
a
Speed [RPM]
Sets the r.p.m. of a record
33 1/3, 45, 78
b
Flutter
Sets the modulation depth
0...100
☞
c
Noise Density
Sets the noise density
0...100
Noise Tone
Sets the noise tone
0...100
d
Noise Level
Sets the noise level
0...100
Src
Selects the modulation source for the noise level
Off...Tempo
Amt
Sets the modulation amount of the noise level
–100...+100
e
Click Level
Sets the click noise level
0...100
☞,
Src Off...Tempo
Selects the modulation source for the click noise level
Amt –100...+100
Sets the modulation amount of the click noise level
f
EQ Trim
Sets the EQ input level
0...100
g
Pre EQ Cutoff [Hz]
Sets the EQ center frequency
300...10.00kHz
Q
Sets the EQ band width
0.5...10.0
Gain [dB]
Sets the EQ gain
–18.0...+18.0dB
h
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Analog Record
Simulation
Pre EQ
Pre EQ
EQ Trim
EQ Trim