Filter
Top Products
Program
P0
P1 P2 P3 P4 P5 P7 P8 P9
7
0–3D: Select Directory
This lets you select the disk (internal hard disk, etc.) and
directory on which the WAVE file created by sampling will
be saved, and specify a filename.
You will also choose this “Select Directory” command when
you want to listen to a WAVE file that was saved on disk.
“Select Directory” can be selected when “Save to” is set to
DISK.
Specifying the save destination for a WAVE file
1 Select the “Select Directory” to access the dialog box.
2 Use the popup button located at the left of “Drive select”
to select the writing-destination drive for sampling.
3 Use the Open button and Up button to move to the
desired directory.
4 In “Name,” specify a name for the WAVE file that will be
written during sampling.
If you check “Take No.,” the file will be saved with a
two-digit “Take No.” added to the end of the filename.
This number will automatically increment each time you
sample. This is convenient when you are sampling
repeatedly, since each sample will be saved with its own
filename.
If “Take No.” is not checked, you can input up to eight
characters in “Name.” If “Take No.” is checked, you can
input up to six characters.
5 Press the Done button to complete the settings.
Playing back a WAVE file
1 Select the “Select Directory” to access the dialog box.
2 Use “Drive Select” and the Open and Up buttons to
select the drive and directory, and select the WAVE file
(44.1 kHz or 48 kHz) that you want to play.
3 Press the SAMPLING [START/STOP] key.
The selected WAVE file will be played.
4 Press the SAMPLING [START/STOP] key once again to
stop playback.
If the WAVE file is mono, the same sound will be output
to L/R.
While the WAVE file is playing back, sound cannot be
produced by playing the keyboard or receiving note
data at MIDI IN. Also, the arpeggiator will stop.
Here you can make basic settings for the program, such as
oscillator mode and scale type.
1–1: Program Basic
1–1a: Oscillator Mode
Oscillator Mode [Single, Double, Drums]
Specifies the Program’s oscillator assignment; whether it
will use one or two oscillators, or a drum kit.
Single: The program will use one oscillator (Oscillator 1,
Filter 1, Amplifier 1). In this case the program will normally
have a maximum of 60-note polyphony.
Double: The program will use two oscillators (Oscillator 1/
2, Filter 1/2, Amplifier 1/2). In this case the program will
normally have a maximum of 30-note polyphony.
Drums: The program will use one oscillator (as when Single
is selected), but Oscillator 1 will be assigned a drum kit
instead of a multisample. In this case the program will nor-
mally have a maximum of 60-note polyphony.
If a program draws one multisample from the ROM
bank, and a second from either the Piano bank or one of
the installed EXB boards, then in this case, a Single pro-
gram can have a maximum of 120-note polyphony, a
Double program a maximum of 60-note polyphony,
and a Drums program a maximum of 120-note polyph-
ony. (☞BG p.15)
1–1b: Voice Assign Mode
Mode (Voice Assign Mode) [Poly, Mono]
Poly: The program will play polyphonically, allowing you
play chords.
Mono: The program will play monophonically, producing
only one note at a time.
Single Trigger [Off, On]
This is available when the “Mode (Voice Assign Mode)”
setting is set to Poly.
On (checked): When the same note is played repeatedly, the
previous note will be silenced before the next note is
sounded, so that the notes do not overlap.
Legato [Off, On]
This is available when the “Mode (Voice Assign Mode)”
setting is set to Mono.
On (checked): Legato is on. When multiple note-on’s occur,
the first note-on will retrigger the sound, and the second and
subsequent note-on’s will not retrigger.
Drive select
Program P1: Edit–Basic
1–1
1–1c
1–1b
1–1a