Filter
Top Products
6
The “Auto +12 dB On” setting will not affect samples
that you recorded to the internal hard disk etc. when
“Save to” (0–3b) is set to DISK. You can use “WAVE
File Play Level” (Global P0: 0-2a) to set the playback
level.
▼ 0–3: Page Menu Command
0–3A: Metronome Setup
Specifies the output destination and volume of the metro-
nome that is sounded when you use “Trigger” Sampling
START SW to begin sampling.
1 Select “Metronome Setup” to access the dialog box.
2 In “BUS (Output) Select,” specify the output destination
of the metronome sound. If you select L/R, the metro-
nome will stop as soon as sampling begins.
3 Set “Level” to specify the volume of the metronome.
4 Press the OK button to apply the settings you made, or
press the Cancel button to return to the state prior to
accessing this dialog box.
The metronome is valid only if “Trigger” is set to Sam-
pling START SW.
0–3B: Optimize RAM
This command optimizes the sample memory (RAM).
When you execute this command, unused memory areas
will be reorganized, allowing the full amount of remaining
to be used.
If you run out of memory, try executing “Optimize RAM.”
The remaining amount of RAM can be checked in Sampling
mode P0: Recording, Memory Status.
1 Select “Optimize RAM” to access the dialog box.
2 Press the OK button to execute the command, or press
the Cancel button to cancel without executing.
If “Auto Optimize RAM” (Global P0: 0–3b) is checked,
RAM will be optimized automatically.
0–3C: Select Bank & Smpl No.
Specifies the RAM bank and sample number into which the
sampled data will be written. You can also specify whether
the sample will automatically be converted to a program
after sampling. “Select Bank & Smpl No.” can be selected if
you have selected RAM as the “Save to” destination.
1 Select the “Select Bank & Smpl No.” to access the dialog
box.
2 In “Bank,” specify the sample memory (RAM) bank to
which the sampled data will be written.
3 In “Sample No.,” specify the writing-destination sample
number. By default, this will be the lowest-numbered
vacant sample number. If you select “----:----No Assign----”
or a sample number that already contains data, the data
will automatically be sampled into the lowest vacant
sample number. If you are sampling in stereo, specify
“Sample No.(L)” and “Sample No.(R).”
4 Set “Auto +12 dB On.”
On (checked): “+12 dB” (Sampling P2: 2–1c) will auto-
matically be turned on for samples you record. Samples
for which “+12 dB” is on will play back approximately
+12 dB louder than if this setting were off.
When you resample a performance in Program, Combi-
nation, or Sequencer modes, you should normally set
“Recording Level” to about –12.0 (dB) so that the record-
ing level will be as high as possible without clipping.
When you resample, the sound will be recorded at the
optimum level for sampled data, but the playback level
at playback will not be as loud as it was during the resa-
mpling process (if “+12 dB” (Sampling P2: 2–1c) is off). In
such cases, you can check the “Auto +12 dB On” check
box when you resample, so that “+12 dB” (Sampling P2:
2–1c) will automatically be on, making the sample play
back at the same level as when it was resampled.
In these modes, the power-on defaults are “Recording
Level” set to –12.0 (dB) and “Auto +12 dB On” turned on.
If you resample a performance in one of these modes
with these settings, the sample will play back at the same
level at which it was resampled.
If you want to monitor your performance in Program,
Combination, or Sequencer mode while sampling only
the external audio signal from AUDIO INPUT etc. (the
“Source BUS” Indiv.1/2 setting: 0–3b), we recommend
that you set “Recording Level” to about +0.0 (dB) and
turn off “Auto +12 dB On” when you resample.
The “Auto +12 dB On” setting is made independently
for Program, Combination, Sequencer, and Sampling
modes.
5 “Convert to” specifies whether the sample will automati-
cally be converted into a program as soon as it has been
sampled. This is convenient when you want to hear the
sound immediately after sampling.
If you check the “Program” check box, the sample will
automatically be converted into a program.
At the right, set “Program” and “MS” to specify the pro-
gram number and multisample number for the con-
verted program.
Set “Orig. Key” (Sampling P0: 0–1b) to specify the loca-
tion of the original key. The multisample will create an
“Index” (Sampling P0: 0–1a) with this key as the “Top
Key” (Sampling P0: 0–1b). The “Orig. Key” will incre-
ment by one after sampling, and the next higher note will
be assigned the next time you sample.
6 Press the OK button to apply the settings you made, or
press the Cancel button to return to the state prior to
accessing this dialog box.
0–1A
0–3A
0–3B
0–3C
0–1A
0–3A
0–3B
0–3D