Filter
Top Products
166
Can’t use the expression pedal or MIDI to control an
effect
In the SYSTEM/MIDI, “Control” tab page, is the effect
selected by “Control Change Assign” enabled?
→ Go to the EFFECT, “EFFRouting” tab page and verify
that the effect is enabled.
Are you using the correct device to control the effect?
→ Control the effect using the device specified by the
“Control Change Device” setting in the SYSTEM/
MIDI, “Control” tab page. (→p.119)
Is the selected effect set to effect program number “000”
(=NO EFFECT) or to an effect program number that does
not include a control function?
If you are controlling via MIDI, does the MIDI channel
number of the D3200 match the MIDI channel of the
transmitting MIDI device? (→p.124)
Is the effect program’s Ctrl setting turned on? (→p.57)
Can’t apply external effect (AUX)
Is the external send level setting set to zero or nearly
zero?
→ Go to the MIXER, SEND (EFF/AUX/REC)
, “AUX1
Send”/“AUX2 Send” tab page, and raise the external
send level.
Is the output of your external effect connected to the
INPUT 1–INPUT 12 jacks, and input to the mixer
channels?
→ Go to the MIXER, CH INPUT/SubMixer
, “Ch Assign”
tab page and make the appropriate assignments.
Have sub input settings been made correctly? (→p.44,
101)
Session Drums
Drum sound is not output
Is the DRUMS key turned off?
Is the DRUMS fader lowered?
Is the rhythm assign setting appropriate?
→ If the rhythm is assigned to a CH Input, input the
rhythm to a mixer channel.
Is the recorder stopped?
→ Press the PLAY key to play back. The rhythm will
sound while the recorder is recording or playing,
If you want to preview the rhythm while the recorder is
stopped, go to the SESSION DRUMS, “SessionDr.” tab
page and turn the RUN button on.
You may have selected a silent drum pattern.
The session drum volume may be too low.
→ Use DRUMS fader to adjust the volume.
Can’t hear the drum
Is the DRUMS key off? (→p.59)
A key does not function when pressed
Some keys do not function while the recorder is playing
or recording.
→ Stop the recorder, and then perform the operation.
Some keys do not function while Scrub is on.
→ Turn off Scrub, and then perform the operation.
(→p.40, 146)
Is a dialog box open?
→ Click either the Yes, No button to close the dialog box.
The 1–16/17–32 key does not work
In the case of a 24-bit song, only sixteen channels are
available, so this key will not function.
MIDI
MIDI sequencer won’t synchronize/MIDI control is
not possible
Are the MIDI cables connected correctly? (→p.11)
A MIDI cable may be broken.
Can’t synchronize using MTC or MIDI Clock
Are the master and slave settings correct? (→p.125)
Does the synchronization signal being output by the
D3200 match the synchronization signal your MIDI
sequencer is receiving?
→ Go to the SYSTEM/MIDI, “MIDI/MMC” tab page
and check the “MIDI Sync” setting. (→p.125)
Are the synchronization settings of your MIDI sequencer
appropriate?
→ Refer to the owner’s manual of your MIDI sequencer.
The D3200 doesn’t receive MMC
In the SYSTEM/MIDI, “MIDI/MMC” tab page, is
“MMC Mode” set to “Receive”?
In the above page, is “MMC Device ID” set to match the
MMC device ID setting of your MIDI sequencer?
(→p.125)
→ For some MIDI sequencers, the MMC device ID setting
may differ.
Is your MIDI sequencer set to transmit MMC?
→ Refer to the owner’s manual of your MIDI sequencer.
Can’t use MIDI to control scenes
Do the MIDI channels of the D3200 and your MIDI
sequencer match?
→ Go to the SYSTEM/MIDI, “MIDI/MMC” tab page
and check the “Global Ch” setting. (→p.125)
Are program changes turned off?
→ Check the settings in the SYSTEM/MIDI, “MIDI/
MMC” tab page. (→p.124)
The D3200 does not synchronize as a slave
→ If the D3200 is set as an MTC slave, it may take several
seconds for synchronization to occur.
→ Do the Frame Rate settings match? (→p.125)
→ If you are using MTC to synchronize, the MIDI se-
quencer to which you are synchronizing must support
MTC.
Can’t control another device via MMC
In the SYSTEM/MIDI, “MIDI/MMC” tab page, is
“MMC Mode” set to “Transmit”?
Is the MMC slave device set so that it will receive MMC?
Does the D3200’s MMC Device ID match the external
MIDI device’s MMC Device ID?
Can’t use MIDI to control mixer parameters
Is the device that is receiving the control changes set to
record all MIDI channels 1–16?
Are control changes turned off?
→ Check the settings in the SYSTEM/MIDI, “MIDI/
MMC” tab page. (→p.124)