Filter
Top Products
46
If the level meter indicates clipping, click the ATT knob icon and
adjust it so that clipping does not occur.
Applying EQ to the playback
(1) Press the REC/PLAY key, and press the channel key of
the channel where you want the EQ applied, setting
that channel to Play mode (key lit green).
(2) Press the EQ key, access the “EQ/ATT” tab page.
(3) Play back the song. (→p.68 “2-1. Normal playback”)
(4) Press the CH SELECT key, use the channel keys to
select the channel to where you want the EQ applied,
and make sure the TRACK/INPUT indicator is set to
“TR.”
(5) Click the ON/OFF button to turn on the EQ.
If this is off, the EQ will not be applied.
(6) Use the Knob Matrix to adjust the EQ settings (→p.107
“2d-1. EQ/ATT”).
If the level meter indicates clipping, click the ATT knob icon and
adjust it so that clipping does not occur.
Master EQ
You can use an four-band full-parametric equalizer to adjust
the tone of the master bus.
(1) Access the EQ, “MasterEQ” tab page.
(2) Click the ON/OFF button to turn on the master EQ.
If this is off, the master EQ will not be applied.
(3) Select the channel whose EQ you want to adjust.
Click the L button if you want to adjust the tone of the
left channel, or click the R button to adjust the tone of
the right channel.
If you click the Link button, adjusting the EQ settings of one
channel will automatically set the other channel to the same
values.
(4) Use the Knob Matrix to adjust the EQ settings (→p.108
“2d-4. Master EQ”)
3-4. EQ library (Storing and recall-
ing EQ settings)
You can store channel EQ settings in the EQ library and recall
them as desired.
A total of one hundred EQ settings are available; 50 presets
and 50 user-writable settings.
Storing EQ settings
(1) Adjust the EQ settings as desired.
Refer to “Channel EQ” on the previous page.
(2) Access the “EQ Library” tab page, and click the Store
button.
The EQ settings that will be stored are the EQ settings of
the channel whose CH SELECT key is on (key lit).
A name will automatically be assigned to the stored EQ
settings; e.g., CH08-I·EQ (channel 8 Input EQ) or CH10-
EQ (channel 10 Track EQ).
(3) If you want to rename the settings, click the Rename
button to display the Rename dialog box.
For the renaming procedure, refer to “1-2. Renaming a
song” (→p.36).
(4) In the library number cell, select the desired save-des-
tination.
Then click the Yes button (or press the panel YES key) to
save the EQ settings.
If you decide not to save, click the No button (or press
the panel NO key).
Recalling EQ settings
(1) Access the “EQ Library” tab page, and click (highlight)
the EQ settings that you want to use.
(2) Press the CH SELECT key, and press the channel key
of the channel where you want to apply the EQ set-
tings.
(3) Click the Recall button to recall the EQ settings.
Verify the recall-destination channel in the Recall dialog
box, and click the Yes button (or press the panel YES
key). If you decide not to recall, click the No button (or
press the panel NO key).
(4) Return to the “EQ/ATT” tab page, check the EQ set-
tings that were recalled, and make adjustments as nec-
essary.
Since channels 25–32 have a two-band EQ with Low and High,
loading four-band EQ library settings into these channels will
have the following result.
• LowMid and HighMid settings will be ignored.
• The Gain and Fc settings for the Low and High bands will be
used as they are, but the Q will be forcibly changed to Shelving.
3-5. Pairing
By specifying adjacent odd-numbered and even-numbered
channels (1–2, 3–4, 5–6…31–32) as a pair, you can adjust the
values of both channels simultaneously by editing the value
of the one of paired channels.
This is convenient when you want to adjust the mixer set-
tings for a stereo source or track.
The following settings can be paired.
• Channel keys when the CH ON key is on
• Channel keys when the REC/PLAY key is on
• EQ/ATT
• REC/EFF/AUX SEND
• Channel fader
•PAN settings
•Group settings
(1)
(2)
(4)
(3)