Filter
Top Products
164
Category: Special Effect
Special Effect
This effect simulates a vacuum tube preamp. You can make
independent settings for two vacuum tubes connected in se-
ries, producing a distinctive and warm sound.
Dry:Wet Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Waveform (LFO Waveform) Triangle, Sine, Saw
Selects LFO Waveform
LFO Speed 0.02...20.00Hz
Sets the LFO speed
LFO Step 0...256
Selects the LFO step
Env.Resp (Envelope Responce) Slow, Medium, Fast
Selects the response speed of envelope control
Env.Sens (Envelope Sensitivity) 0...100%
Sets the sensitivity of envelope control
47: Mono Wah
Control (Control Source) Envelope, LFO, Manual
Switches the control source
Wah.Type Y-CRY, RM-A, RM-B, J-CRY, VOX, M-VOX
Selects the wah type
Env.Resp (Envelope Responce) Slow, Mediumd, Fast
Selects the response speed of envelope control
Env.Sens (Envelope Sensitivity) 0...100%
Sets the sensitivity of envelope control
Waveform (LFO Waveform) Triangle, Sine, Saw
Selects LFO Waveform
*LFO Speed 0.02...20.00Hz
Sets the LFO speed
LFO Step 0...256
Selects the LFO step
*Manual (Manual Control) 0...100
Sets the control position manually
DirectMix (Direct Mix Level) 0...100%
Adjusts the mix level of the direct sound
Wah Level 0...100
Sets the wah level
48: Mn.Analog Record
(Mono Analog Record)
RPM 33 1/3, 45, 78
Sets the r.p.m. of a record
Wah (Wah Flutter) 0...100%
Sets the depth by which the record is warped
Bend 0...100%
Sets the width by which the record is warped
Dry:Wet Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
ClickLevel (Click Noise Level) 0...100%
Sets the level of click noise
ClickAngle (Click Angle) 0...100
Sets the angle of the scratch on the surface of the record
LoDamp (Low Damp) THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp) 53Hz...20.0kHz, THRU
Sets the damping amount in the high range
ClickPoint 0...100
Sets the distance of the scratch from the warped area
WhiteLevel (White Noise Level) 0...100%
Sets the level of white noise
NoiseLoCut (Noise Low Cut) THRU, 21Hz...8.00kHz
Sets the low-cut frequency for the noise
NoiseHiCut (Noise High Cut) 53Hz...20.0kHz, THRU
Sets the high-cut frequency for the noise
49: Mn.Ring Modulator
(Mono Ring Modulator)
Oscilator (Oscilator Frequency) 0...12.00kHz
Sets the oscillator frequency
*LFO Speed 0.02...20.00Hz
Sets the LFO speed of the oscillator frequency modulation
*LFO Depth 0...100%
Sets the depth of LFO modulation for the oscillator frequency
Dry:Wet Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Delay (Delay Time) 0...2.730sec (1.360sec)
Sets the delay time
Feedback –100...+100%
Sets the feedback amount
HiDamp (High Damp) 53Hz...20.0kHz, THRU
Sets the damping amount in the high range
In Level (Input Level) 0...100%
Sets the input level to the effect
50: Tube Pre Amp Sim
(Tube PreAmp Simulator)
Tube1.Gain –24.0...+24.0dB
Sets the gain of tube circuit 1
Tube1.Sat (Tube1 Satulation) 0...100%
Sets the amount of saturation for tube circuit 1
Tube2.Gain –24.0...+24.0dB
Sets the gain of tube circuit 2
Tube2.Sat (Tube2 Satulation) 0...100%
Sets the amount of saturation for tube circuit 2
Tb1.LoCut (Tube1 Low Cut) THRU, 21Hz...8.00kHz
Sets the amount of low-frequency attenuation for tube circuit 1
Tb1.HiCut (Tube1 High Cut) 53Hz...20.0kHz, THRU
Sets the amount of high-frequency attenuation for tube circuit 1
Tb2.LoCut (Tube2 Low Cut) THRU, 21Hz...8.00kHz
Sets the amount of low-frequency attenuation for tube circuit 2
Tb2.HiCut (Tube2 High Cut) 53Hz...20.0kHz, THRU
Sets the amount of high-frequency attenuation for tube circuit 2
Tube1Bias 0...100%
Sets the bias for tube circuit 1
Tb1.Phase (Tube1 Phase) Normal, Inverted
Sets the output phase of tube circuit 1
Tube2Bias 0...100%
Sets the bias for tube circuit 2
Out Level (Output Level) –48.0...0.0dB
Sets the output level