Filter
Top Products
iv
Cautions when using the CD-R/
RW drive
• During CD reading and writing operations, keep the unit
in a horizontal position.
• Do not use the unit in extremely cold or hot locations.
• Do not use the unit in extremely humid locations.
• Do not use the unit in dusty or smoky locations.
• Do not subject the unit to vibration or strong physical
shock. In particular, this unit is vulnerable to shock during
CD reading and writing operations.
• Normally, you will be able to open the CD tray by press-
ing the eject button. However if this fails, you can forcibly
eject the tray by inserting a thin object (such as a straight-
ened paper clip) into the emergency eject hole.
• Do not store the unit in hot or humid locations.
• Never touch the focusing lens.
• Do not use commercially available lens cleaners.
• Do not transport the unit with a disc left in the tray.
• Do not leave the unit with the disc tray open.
CD-R/RW handling
Please observe the following points when handling discs.
Failure to observe these points may cause problems such as
data not being written correctly, loss of recorded data, or
drive malfunction.
• Do not leave discs in direct sunlight, or in locations of
high temperature or high humidity.
• Do not touch the surface of a disc. Hold a disc by its
edges.
• Remove dust or dirt from the surface of a disc. To remove
dust, use an air duster or cleaner.
• Do not affix labels to a disc, or write on a disc in locations
other than specified.
• Do not use chemicals or detergent to wipe a disc.
• Do not bend or drop a disc.
Responsibility for loss of data
Korg Corporation will accept no responsibility for any dam-
ages (direct or indirect, whether sustained by the customer or
by a third party) resulting from loss of or damage to data
written on a CD-R or CD-RW disc.
Printing conventions in this
manual
Differences between the D32XD and D16XD
In the text and illustrations of this manual, explanations
enclosed by [* ] refer to the D16XD. Unless there are sig-
nificant differences, the illustrations and LCD screens
are taken from the D32XD.
Keys, buttons, and knobs
Words or values printed on the panel, such as
MASTER
fader or
REC/PLAY
key are printed in bold type, and
parameter values are printed in
bold type
within
“dou-
ble quotation marks.”
Bold type is also used to indicate content within the text
that we wish to emphasize.
Parameters that appear in the LCD screen “ ”
Parameters that appear in the LCD screen are printed
within “
double quotation marks
.” However,
bold type
is also used for screen items such as the
Yes
button and
CH
cell.
The D32XD/D16XD uses Korg’s TouchView LCD tech-
nology, allowing a parameter, cell, button, or icon dis-
played on the screen to be selected simply by touching
it. For most operations, you can also use the cursor keys
(
√
,
®
,
π
,
†
) to move to the desired parameter, and
press the
ENTER
key to make a selection.
The example operations described in this manual mainly
use the TouchView panel.
Steps (1) (2) (3) ...
Steps in a procedure are indicated as (1) (2) (3) ...
(
→
p.
■■
)
This indicates a reference page within this manual.
, ,
These symbols respectively indicate points of caution,
notes of advice, or examples.
..., “xx” tab page
This indicates a page displayed in the LCD screen. To
access this page, press the ... key of the top panel, and
then press the “xx” tab in the LCD screen.
You can use the screen to move between tab pages.
..., ...
, “xx” tab page
The
MIXER
key and
CD
key of the top panel display a
page jump menu in the LCD screen before displaying
the tab pages. Press the ...
button in the LCD screen, and
then press the “xx” tab. When you press the
MIXER
key
or
CD
key, you will return to the page jump menu selec-
tion screen.
LCD screens
The parameter values shown in the LCD screens printed
in this manual are explanatory examples, and may not
necessarily match the displays that appear on your
D32XD/D16XD.
Illustrations of the D32XD/D16XD
Unless otherwise specified, illustrations of the D32XD/
D16XD printed in this manual assume the optional 8-
channel analog input board (AIB-8) is installed.