Filter
Top Products
166
Appendices
Troubleshooting
Power does not turn on
Is the power cable connected to an outlet? (→p.1)
Is the rear panel POWER ON (power supply) switch
turned on? (→p.1)
Nothing appears in the display
Is the top panel power on key lit? (→p.1)
Is the contrast adjusted correctly? (→p.10)
Vertical lines are visible in the display
Depending on the content of the display, vertical lines
may be visible in the display, but this is not a
malfunction.
→ If the screen is difficult to read, adjust the contrast and
angle (→p.10).
TouchView response is poor
Press the SYSTEM key, and use the “Control” tab page
item “Touch Panel Calibration” to calibrate the touch
panel (→p.95).
No sound
Is the power of the D32XD/D16XD or a connected
device turned off? (→p.1)
Is the MASTER fader, MONITOR LEVEL knob, or
PHONES 1, 2 VOLUME knobs set to low?
Is the channel volume level set to low?
The actual volume level may not match the fader posi-
tions if pairing has been used and then switched off, or
after automation has been used.
→ Go to the MIXER, FADER/PAN/AUTOMATION
,
“Fader Pan” tab page, and raise and lower the fader to
match the fader position to the actual volume. Then
adjust the fader to an appropriate level.
Is the Solo function activated?
→ If Solo is being used, you will not hear channels that
are not being soloed.
Can’t hear the playback
If the REC/PLAY key set to PLAY? (→p.8)
Is the CH ON key turned on? (→p.9)
Has solo been turned on, so that other tracks are not
heard? (→p.9, 97)
If you have selected Cue, could the cue level of the
channels be lowered?
→ Access the MIXER, SOLO/MONITOR
, “CueLevel”
tab page and raise the cue level. (→p.51)
Could the Trim level be turned down in the EFFECT,
“InsertEFF” tab page?
→ If a channel is assigned to an insert effect, the volume
of that channel is determined by the Trim setting even
if the insert effect is set to NO EFFECT.
Is CD Monitor set to on? (→p.123)
Is the 1–16/17–32 key set correctly? (→p.10)
Input sound is inaudible or too soft
Is the TRIM knob raised to an appropriate level?
After connecting your audio source to an input jack, did
you assign it to a mixer channel?
→ In the MIXER, INPUT/OUTPUT/CH ASSIGN
, “Ch
Assign” tab page, assign the source to a mixer channel.
(→p.42)
Verify that audio is being input.
→ Press the METER key, and in “Meter Trk View,” set
“Select Level Meter Position” to “CH-Input.” Watch
the meters to verify that audio is being input to each
mixer channel (→p.42).
Are you using the analog compressor? (→p.46)
Is the REC/PLAY key set to REC? (→p.8)
Are the monitor settings appropriate?
→ In the MIXER, SOLO/MONITOR
, “Monitor” tab
page, select the signal that you want to monitor (nor-
mally, turn “MasterLR” On). If you have turned
“Rhythm” or “Cue” “On,” raise their volume levels.
(→p.50)
Is the CH ON key turned on? (→p.9)
Is the PAD key on?
Are you using INPUT1 and GUITAR IN simultaneously?
→ INPUT1 and GUITAR IN are shared. If a guitar is con-
nected to GUITAR IN, you cannot use INPUT1.
If cue is selected, the cue level of each channel may have
been lowered.
→ In the MIXER, SOLO/MONITOR
, “CueLevel ” tab
page. (→p.51)
Is the 1–16/17–32 key set correctly? (→p.10)
Could the Trim level be turned down in the EFFECT,
“InsertEFF” tab page?
→ If a channel is assigned to an insert effect, the volume
of that channel is determined by the Trim setting even
if the insert effect is set to NO EFFECT.
Can’t hear an audio CD inserted in the CD-R/RW
drive
Is the output of the internal CD-R/RW drive correctly
assigned to the mixer channels?
→ Go to the MIXER, INPUT/OUTPUT/CH ASSIGN
,
“Ch Assign” tab page, and assign the CD output to the
appropriate mixer channels.
Was the D32XD/D16XD subjected to vibration or
impact?
The D32XD/D16XD’s CD-R/RW drive is a removable
drive.
→ Verify that the CD-R/RW drive is installed correctly.
(→p.181 “Checking the internal CD-R/RW drive”)
Can’t hear sound other than the audio CD
Is the CD, CD PLAYER CD Monitor button on?
→ If the CD Monitor button is on, all sounds other than
the internal CD drive will be muted. Turn this button
off except when you want to use the internal CD drive
to monitor an audio CD. (→p.123)
No sound from AUX OUT
“Can’t apply external effect (AUX OUT)” (→p.168)