Filter
Top Products
169
Appendices
TroubleshootingVarious messages
More about drives
and files
Installing the
options
Specifications
Various listsGlossaryIndex
MIDI
MIDI sequencer won’t synchronize/MIDI control is
not possible
Are the MIDI cables connected correctly? (→p.14)
A MIDI cable may be broken.
Can’t synchronize using MTC or MIDI Clock
Are the master and slave settings correct? (→p.93)
Does the synchronization signal being output by the
D32XD/D16XD match the synchronization signal your
MIDI sequencer is receiving?
→ Go to the MIDI/SYNC, “MIDI/MMC” tab page and
check the “MIDI Sync” setting. (→p.131)
If “Tempo Source” is set to “Tempo Track,” is MIDI
clock or tap tempo data recorded in the tempo track?
(→p.63)
Are the synchronization settings of your MIDI sequencer
appropriate?
→ Refer to the owner’s manual of your MIDI sequencer.
The D32XD/D16XD doesn’t receive MMC
In the MIDI/SYNC, “MIDI/MMC” tab page, is “MMC
Mode” set to “Receive”?
In the above page, is “MMC Device ID” set to match the
MMC device ID setting of your MIDI sequencer?
(→p.131)
→ For some MIDI sequencers, the MMC device ID setting
may differ.
Is your MIDI sequencer set to transmit MMC?
→ Refer to the owner’s manual of your MIDI sequencer.
Can’t use MIDI to control scenes
Do the MIDI channels of the D32XD/D16XD and your
MIDI sequencer match?
→ Go to the MIDI/SYNC, “MIDI/MMC” tab page and
check the “Global Ch” setting. (→p.131)
Are program changes turned off?
→ Check the settings in the MIDI/SYNC, “MIDI/MMC”
tab page. (→p.131)
The D32XD/D16XD does not synchronize as a slave
→ If the D32XD/D16XD is set as an MTC slave, it may
take several seconds for synchronization to occur.
→ Do the Frame Rate settings match? (→p.131)
→ If you are using MTC to synchronize, the MIDI se-
quencer to which you are synchronizing must support
MTC.
Can’t control another device via MMC
In the MIDI/SYNC, “MIDI/MMC” tab page, is “MMC
Mode” set to “Transmit”?
Is the MMC slave device set so that it will receive MMC?
Does the D32XD/D16XD’s MMC Device ID match the
external MIDI device’s MMC Device ID?
Can’t use MIDI to control mixer parameters
Is the device that is receiving the control changes set to
record all MIDI channels 1–16?
Are control changes turned off?
→ Check the settings in the MIDI/SYNC, “MIDI/MMC”
tab page. (→p.131)
CD-R/RW
Can’t write
No further data can be written to a CD-R/RW disc that
has been finalized. (→p.123)
No data can be written to a CD-RW disc that contains
data written by another device.
Failed while writing to CD.
→ Select an appropriate speed for writing to CD-R/RW.
If you failed while writing at the highest speed, try a
slower speed. In some cases if you are using a disc that
is optimized for high-speed writing, you may be una-
ble to write at low speeds.
→ Try a different disc.
Can’t select some speeds when writing to CD.
→ The speeds that you can select will differ depending on
the type of disc.
Can’t create an audio CD.
→ Use a blank disc.
Can’t play back on an audio CD player
Did you finalize the disc?
→ In the CD, CD WRITER
, “CD Utility” tab page, press
the Finalize button to finalize the disc. (→p.125)
Did you use CD-R disc?
→ Some CD players are unable to play back CD-RW disc.
We recommend that you use CD-R disc.
Have you tried using a different type of disc?
→ Even when the recommended media is used, some CD
players are unable to play back certain types of CD-R/
RW disc. You may be able to play back successfully if
you use a different type of CD-R/RW disc.
Audio files
Can’t preview
Is the audio file format supported?
→ Preview a WAV file of a supported format. (→p.85,
146)
USB
Computer does not recognize the D32XD/D16XD
Is the USB cable connected correctly? (→p.13)
Is the D32XD/D16XD set to USB Slave mode? (→p.92)
Error occurred when you disconnected the D32XD/
D16XD from the computer
Use the correct procedure to disconnect. (→p.92)
When you connected the D32XD/D16XD, the com-
puter asked you to install software or a device driver
Does the operating system of your computer support the
D32XD/D16XD? (→p.92)
ADAT
“ADAT.Out” tab page is not displayed
Is the optional ADAT I/O board (DIB-8) installed?
Could you have selected a 96 kHz/24-bit song?
Troubleshooting