Filter
Top Products
Index - 8
• Start complete signal............................... 3-15
• Synchronization flag signal..................... 3-15
Simultaneous start....................................... 10-12
Simultaneous starting axis start data No. (Axis 1
start data No.) (
Cd.30
)............................. 5-166
Simultaneous starting axis start data No. (Axis 2
start data No.)(
Cd.31
).............................. 5-166
Simultaneous starting axis start data No. (Axis 3
start data No.)(
Cd.32
).............................. 5-166
Simultaneous starting axis start data No. (Axis 4
start data No.)(
Cd.33
).............................. 5-166
Skip command (
Cd.37
)............................ 5-168
Skip function ................................................ 12-66
Skip operation program................................. 6-47
Slight vibration suppression control selection
(
Pr.142
)........................................................ 5-76
Slot................................................................... 2-6
Software stroke limit function...................... 12-29
Software stroke limit lower limit value (
Pr.13
)
....................................................................... 5-30
Software stroke limit selection (
Pr.14
)..... 5-30
Software stroke limit upper limit value (
Pr.12
)
....................................................................... 5-30
Software stroke limit valid/invalid setting
(
Pr.15
)....................................................... 5-30
S-pattern acceleration/deceleration processing
method......................................................... 12-87
S-pattern proportion (
Pr.35
)...................... 5-40
Special start instruction (
Da.13
) .............. 5-109
Special start data instruction code setting value
(
Md.36
)...................................................... 5-138
Special start data instruction parameter setting
value (
Md.37
)............................................ 5-138
Special start repetition counter (
Md.41
)... 5-140
Specifications of input/output interfaces....... 3-18
Specifications of input/output signals ........... 3-14
Speed change 0 flag ................................... 5-134
Speed change function ............................... 12-42
Speed change program ................................ 6-43
Speed change request (
Cd.15
) ............... 5-156
Speed control 10 x multiplier setting for degree
axis (
Pr.83
) ................................................ 5-44
Speed control 10 x multiplier setting for degree
axis function .............................................. 12-101
Speed designation during OP shift (
Pr.56
)
........................................................................5-58
Speed differential compensation (
Pr.129
)...5-72
Speed integral compensation (
Pr.128
)........5-72
Speed limit function .....................................12-23
Speed limit value (
Pr.8
).............................5-28
Speed loop gain (
Pr.127
).............................5-70
Stop command processing for deceleration
stop selection (
Cd.42
)................................5-148
Speed-position function selection (
Pr.81
)..5-34
Speed switching mode (
Pr.19
)..................5-34
Speed-position switching control (ABS mode)
........................................................................9-91
Speed-position switching control (INC mode)
........................................................................9-86
Speed-position switching control movement
amount change register (
Cd.23
) ..............5-162
Speed-position switching control positioning
amount (
Md.29
).........................................5-132
Speed-position switching enable flag (
Cd.24
)
......................................................................5-164
Speed-position switching latch flag.............5-134
Speed-position switching signal ....................3-18
Spiral interpolation .........................................9-61
SSCNET
.................................................... A-15
SSCNET
cable length..................................3-3
Standard speed switching mode...................9-12
Start Hour (
Md.5
) ......................................5-120
Start complete signal .....................................3-15
Start data No. (
Da.12
) ..............................5-109
Start data pointer being executed (
Md.43
)
......................................................................5-140
Start details setting program..........................6-53
Start history..................................................5-120
Start history pointer (
Md.8
) .......................5-122
Start information (
Md.3
)............................5-120
Start Minute: second (
Md.6
).....................5-120
Start No. (
Md.4
) ........................................5-120
Start positioning data No. setting value
(
Md.38
)......................................................5-138
Start program .................................................6-55
Start program for high-level positioning control
......................................................................10-23
Status (
Md.31
)...........................................5-134