Filter
Top Products
Reference Song Mode
Song Record mode Song Record Standby mode
223
Owner’s Manual
Event This parameter is available when the Recording Type is set to “step.” This lets you specify the event type to be
entered.
Settings: note, p.bend (pitch bend), CC#000~#119 (Control Change)
RecTrack Determines the track to be recorded.
Pressing the [F6] button lets you switch between Single Track recording and All Track recording.
Settings: tempo, scene, 1~16, multi
(Tempo) Determines the Song tempo.
Settings: 001.0 ~300.0
Meas (Measure) Determines the measure from which Song recording will be started.
[F2] VOICE
In this display you can set the voice related parameters for the recording track. The settings here affect the Part for which the receive channel (set in the Mixing
mode) matches the transmit (output) channel of the recording track.
Voice Determines the voice used in the recording track. When the cursor is located here, you can select a voice by using
the BANK, GROUP, NUMBER buttons and the Category Search function (page 62). You can also select a Sample
Voice obtained via the Sampling function.
Volume Determines the volume of the recording track.
Settings: 0 ~ 127
Pan Determines the stereo pan position of the recording track.
Settings: L63 (Left) ~ C (Center) ~ R63 (Right)
InsEF
(Insertion Effect Part Switch)
Determines whether the Insertion effects are applied to the recording track or not.
Settings: on, off
(Tempo) Determines the Song tempo.
Settings: 001.0 ~300.0
Meas (Measure) Determines the measure from which Song recording will be started.
[F3] ARP (Arpeggio)
From this display you can set parameters related to the Arpeggio of the recording track.
Bank, Ctgr (Category), Type These three parameters determine the Arpeggio Type. The three-letter prefix number before the Type name
indicates the number within the selected Category.
Settings: Refer to the separate Data List.
VelLimit (Velocity Limit) Determines the lowest and highest velocity which can trigger the Arpeggio playback. The Arpeggio plays when you
play notes at velocities within this range.
Settings: 1 ~ 127
Hold Determines whether the Arpeggio playback is “held” or not. When this is set to “on,” the Arpeggio cycles
automatically, even if you release your fingers from the keys, and it continues to cycle until the next key is pressed.
Settings: sync-off, off, on
n About sync-off, see page 191.
PartSw (Part Switch) Determines whether Arpeggio is on or off for the tone generator Part corresponding to the recording track.
Settings: off, on
Meas (Measure) Determines the measure from which Song recording will be started. This parameter is same as the Meas parameter
in the [F1] SETUP display.
[SF1] ARP1 (Arpeggio 1) - [SF5]
ARP5 (Arpeggio 5)
You can register the desired Arpeggio types to these buttons and call them up any time during your keyboard
performance. Refer to page 123 in the Quick Guide section.
[F4] RECARP (Record Arpeggio)
RecArp (Record Arpeggio) Determines whether the sequence data played by Arpeggio is recorded to the Song track or not. When this is set to
on, the played sequence data is recorded.
Settings: off, on
OutputSwitch Determines whether the sequence data played by Arpeggio during recording is output via MIDI or not. When this is
set to on, the played sequence data by Arpeggio during recording is output via MIDI.
Settings: off, on
TransmitCh (Transmit Channel) Determines the MIDI transmit channel of the Arpeggio playback during recording.
Settings: 1 ~ 16, KbdCh
[F5] CLICK
Pressing the [F5] button lets you turn the click sound (metronome) on/off for recording.