Filter
Top Products
Basic Operation
Knob (KN) and Control Slider (CS)
50
Owner’s Manual
Knob (KN) and Control Slider (CS)
Knob (KN)
You can change the brightness and tone characteristics of the current Voice or Performance in realtime by turning the knobs
while you play. Rotating it to the right (clockwise) increases the program number, while rotating it to the left (counter-clockwise)
decreases it. You can select the function set assigned to the knobs among the following seven sets by pressing the appropriate
[KNOB CONTROL FUNCTION] button.
Function sets assigned to the Knobs (KN)
* For Drum Voices, this affects the release time for all played notes, whether held or released.
** Available only when setting the Zone Switch to on in the Master Mode (page 137)
When pressing any of the [KNOB CONTROL FUNCTION] buttons, the lamp(s) of the buttons will light according to the above
table and the status of the Knobs and Control Sliders (currently assigned functions and set values) is shown on the LCD display.
The appearance of the knob in the display indicates the actual control status of the knob. When a knob indication is black, the
control knob on the panel affects the sound. When an indication is white, moving the panel knob does not affect the sound, until
the current value is reached (after which the indication turns black, indicating normal control).
Operation
Button of which the
lamp is turned on
Functions controlled by each Knob
KN1 (Knob 1) KN2 (Knob 2) KN3 (Knob 3) KN4 (Knob 4)
When pressing the [PAN/
SEND] button
[PAN/SEND] button Pan (stereo position)
of the Voice/
Performance
Reverb Send Level Chorus Send Level Tempo of the Song/
Pattern/Arpeggio
playback
When pressing the [TONE]
button
[TONE] button Filter Cutoff
Frequency (degree of
brightness)
Resonance (the level
of the signal in the
area of the cutoff
frequency)
Attack Time of the
sound
Release Time of the
sound (decay time
after the key is
released)*
When pressing the [ARP
FX] button
[ARP FX] button Swing degree of the
Arpeggio playback
Gate time (length) of
the Arpeggio
playback
Velocity of the
Arpeggio playback
Arpeggio playback
time
When pressing the [EQ]
button
[EQ] button Low band of the
Master EQ in the
Voice/Performance
mode, part EQ in the
Song/Pattern mode
Low-mid band of the
Master EQ in the
Voice/Performance
mode, Mid band of
the Part EQ in the
Song/Pattern mode
High-mid band of the
Master EQ in the
Voice/Performance
mode. (Not available
in the Song/Pattern
mode.)
High band of the
Master EQ in the
Voice/Performance
mode, part EQ in the
Song/Pattern mode
When pressing the [PAN/
SEND] button and the
[TONE] button
simultaneously
[PAN/SEND] button
[TONE] button
Function assigned from the [UTILITY] → [F4]
CTLASN → [SF2] ASSIGN display (page 263) in
the Utility mode
Function assigned for each Voice from the
[VOICE] → [EDIT] → [COMMON] → [F4]
CTLSET display (page 155)
When pressing the [TONE]
button and the [ARP FX]
button simultaneously**
All the buttons are off Function assigned for each Master from the [MASTER] → [EDIT] → Zone selection → [F5] KN/CS
display (page 140)
When pressing the [ARP
FX] button and the [EQ]
button simultaneously
[ARP FX] button
[EQ] button
Function assigned to the Master Effect parameters from the [UTILITY] → [F4] CTLASN → [SF5] MEF
display.
KNOB
CONTROL
FUNCTION
SWING
CUTOFF
PAN
ASSIGN A
GATE TIME
RESONANCE
REVERB
ASSIGN B
VELOCITY
ATTACK
CHORUS
ASSIGN 1
UNITMULTIPLY
RELEASE
TEMPO
ASSIGN 2
LOW
KN
1
LOW MID
KN
2
HIGH MID
KN
3
HIGH
KN
4
ARP FX
EQ
TONE
ASSIGN
PAN/SEND
Tu rning these Knobs will affect the sound.
Tu rning these Knobs will not affect the sound.