Filter
Top Products
Effects Parameters
332 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section
❏ DELAY→REV
One input, two output delay and reverb effects in series.
❏ DIST→DELAY
One input, two output distortion and delay effects in
series.
❏ MULTI FILTER
Two input, two output 3-band multi-filter (24 dB/octave).
❏ FREEZE
One input, one output basic sampler.
Parameter Range Description
DELAY L 0.0–1000.0 ms Left channel delay time
DELAY R 0.0–1000.0 ms Right channel delay time
FB. DLY 0.0–1000.0 ms Feedback delay time
FB. GAIN –99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
DELAY HI 0.1–1.0
Delay high-frequency feedback
ratio
HPF
THRU, 21.2 Hz–
8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
DLY.BAL 0–100%
Delay and delayed reverb balance
(0% = all delayed reverb, 100% =
all delay)
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
REV HI 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1.
(Maximum value depends on the tempo setting)
Used in conjunction with TEMPO
to determine left channel DELAY L
NOTE R *1
Used in conjunction with TEMPO
to determine right channel DELAY
R
NOTE FB *1
Used in conjunction with TEMPO
to determine FB. DLY
Parameter Range Description
DST TYPE
DST1, DST2, OVD1,
OVD2, CRUNCH
Distortion type (DST = distortion,
OVD = overdrive)
DRIVE 0–100 Distortion drive
MASTER 0–100 Master volume
TONE –10 to +10 Tone control
N. GATE 0–20 Noise reduction
DELAY 0.0–2725.0 ms Delay time
FB. GAIN –99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
HI. RATIO 0.1–1.0 High-frequency feedback ratio
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
DLY.BAL 0–100%
Distortion and delay balance (0%
= all distortion, 100% = all
delayed distortion)
SYNC OFF/ON Tempo parameter sync on/off
DLY.NOTE
*1
*1.
(Maximum value depends on the tempo setting)
Used in conjunction with TEMPO
to determine DELAY
MOD.NOT
E
*2
*2.
Used in conjunction with TEMPO
to determine FREQ.
Parameter Range Description
TYPE 1 HPF, LPF, BPF
Filter 1 type: high pass, low pass,
band pass
TYPE 2 HPF, LPF, BPF
Filter 2 type: high pass, low pass,
band pass
TYPE 3 HPF, LPF, BPF
Filter 3 type: high pass, low pass,
band pass
FREQ. 1 28.0 Hz–16.0 kHz Filter 1 frequency
FREQ. 2 28.0 Hz–16.0 kHz Filter 2 frequency
FREQ. 3 28.0 Hz–16.0 kHz Filter 3 frequency
LEVEL 1 0–100 Filter 1 level
LEVEL 2 0–100 Filter 2 level
LEVEL 3 0–100 Filter 3 level
RESO. 1 0–20 Filter 1 resonance
RESO. 2 0–20 Filter 2 resonance
RESO. 3 0–20 Filter 3 resonance
Parameter Range Description
REC MODE MANUAL, INPUT
In MANUAL mode, recording is
started by pressing the REC and
PLAY buttons. In INPUT mode,
Record-Ready mode is engaged by
pressing the REC button, and
actual recording is triggered by the
input signal.
REC DLY
–1000 to +1000
ms
Recording delay. For plus values,
recording starts after the trigger is
received. For minus values, record-
ing starts before the trigger is
received.
TRG LVL –60 to 0 dB
Input trigger level (i.e., the signal
level required to trigger recording
or playback)
TRG MASK 0–1000 ms
Once playback has been triggered,
subsequent triggers are ignored for
the duration of the TRG MASK
time.
PLY MODE
MOMENT,
CONTI., INPUT
In MOMENT mode, the sample
plays only while the that the PLAY
button is pressed. In CONT mode,
playback continues once the PLAY
button has been pressed. The
number of times the sample plays
is set using the LOOP NUM param-
eter. In INPUT mode, playback is
triggered by the input signal.
START
*1
*1. 0.0–5941.0 ms (fs=44.1 kHz), 0.0 ms–5458.3 ms (fs=48 kHz), 0.0–
2970.5 ms (fs=88.2 kHz), 0.0 ms–2729.2 ms (fs=96 kHz)
Playback start point in milliseconds
END 1 Playback end point in milliseconds
LOOP 1 Loop start point in milliseconds
LOOP
NUM
0–100 Number of times the sample plays
START
[SAMPLE]
0–262000 Playback start point in samples
END
[SAMPLE]
0–262000 Playback end point in samples
LOOP
[SAMPLE]
0–262000 Loop start point in samples
PITCH
–12 to +12 semi-
tones
Playback pitch shift
FINE –50 to +50 cents Playback pitch shift fine
MIDI TRG OFF, C1–C6, ALL
PLAY button can be triggered by
using MIDI Note on/off messages.