Filter
Top Products
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 381
Information shown
in the display
Function
menu
Global
functions
Output
functions
Input
functions
Appendices
General Specifications
PM5D/PM5D-RH
You paired input channels, but the
signal phase is incorrect
❍ Set the paired input channels to the same phase setting. Even when channels are paired, the phase set-
tings are not linked. (➥ p.53)
When you recall a scene, some
channels/parameters are not
updated
❍ Could those channels/parameters be set to Recall Safe or Selective Recall? (➥ p.92, 94)
You turn on a CUE button in the
EFFECT PARAM screen, but it is
automatically defeated
❍ This is defeated automatically when you switch screens in the display. (➥ p.167)
Can’t make boost settings with the
GEQ
❍ In the GEQ PARAM screen, could LIMIT be set to –24 dB? (➥ p.119)
When you recall a scene, it takes a
certain amount of time for the faders
to stop
❍ Could you have specified a fade time? (➥ p.95)
The panel LEDs or LCD display are
too dark / too bright
❍ In the UTILITY function PREFERENCE 2 screen, use the BRIGHTNESS setting to adjust the brightness.
(➥ p.206)
Can’t control the DSP5D that’s
cascade-connected to the PM5D
❍ Are the PM5D and DSP5D correctly cascade-connected?
❍ In the SYS/W.CLOCK function MIXER SETUP screen, is CASCADE CONNECTION set to the correct type?
❍ If the units are cascade-connected via the DCU5D, could two Ethernet cables be connected? To allow bi-
directional communication, connect one Ethernet cable between the DCU5D and DSP5D.
❍ Is the DSP5D’s machine ID number set correctly?
❍ In the SYS/W.CLOCK function MIXER SETUP screen, is the setting CASCADE ENABLED?
❍ Have you used a user-defined key or FADER MODE key to select the machine that you want to control
from the PM5D?
MIX channel signal is not sent from
MIX OUT connector
❍ For the output channel, is a MIX channel patched to the MIX OUT jack?
Can’t load from memory card
❍ Is the memory card formatted as FAT16?
❍ In the UTILITY function SECURITY screen, is the LOAD LOCK button turned off?
Sampling Frequency
Internal: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
External: 44.1 kHz (–10%) to 48 kHz (+6%)
88.2 kHz (–10%) to 96 kHz (+6%)
Signal Delay
PM5D: Less than 2.3 ms INPUT to STEREO A,B (@Fs = 48 kHz)
Less than 1.15 ms INPUT to STEREO A,B (@Fs = 96 kHz)
PM5D-RH: Less than 2.5 ms INPUT to STEREO A,B (@Fs = 48 kHz)
Less than 1.25 ms INPUT to STEREO A,B (@Fs = 96 kHz)
Fader 100mm motorized x38
Fader Resolution +10 to –138, –∞ dB (1024 steps/100 mm)
Maximum Voltage Gain
PM5D: 84 dB INPUT1-48 to Each Output
PM5D-RH: 86 dB INPUT1-48 to Each Output
Crosstalk (@1kHz) –80 dB Adjacent Input Channels (INPUT1-48), GAIN: Min.
Dimensions 1551 x 950 x 283 mm (W x D x H)
Net Weight
PM5D: 98 kg
PM5D-RH: 97 kg
Power Requirements
PM5D: 480W, DC 24V, 20A (Use PW800W Only)
PM5D-RH: 528W, DC 24V, 22A (Use PW800W Only)
Operation free-air Temperature Range +10 °C to +35 °C
Storage Temperature Range –20 °C to +60 °C
Included Accessories
Owner’s Manual
Gooseneck Lamps x 3
Power Supply PW800W Connection Cable
Optional Accessories
mini YGDAI cards
Power Supply PW800W
Power Supply Link Cable PSL120