Filter
Top Products
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 59
6
Output channel operations
Hint
You can fix the encoders in the above state by rapidly press-
ing the MIX [SEL] key twice. To return to the previous state,
press any MIX [SEL] key or MATRIX [SEL] key.
5
If you want the meters of the panel to indi-
cate the output level of the MIX channels,
press the [MIX/MATRIX] key of the meter
section.
Hint
The send levels from MIX channels to MATRIX buses can
also be edited in the display. For details, refer to p.262.
❏ Sending signals from MIX channels to
the STEREO bus
Here’s how signals sent from input channels to MIX buses
can be output to the STEREO bus.
1
Make sure that appropriate signals are being
sent from input channels to the MIX buses.
2
Press the [MIX MASTER] key in the MIX
section.
3
Turn on the MIX [ON] key for the MIX chan-
nels whose signals you want to send to the
STEREO bus.
4
Press the MIX [SEL] key of the channel whose
signal you want to send to the STEREO bus,
and turn on the [TO STEREO] key of the
SELECTED CHANNEL section.
5
To adjust the pan of the signal sent from the
MIX channel to the STEREO bus, press the MIX
[SEL] key of the desired MIX channel and turn
the STEREO [PAN] encoder of the SELECTED
CHANNEL section.
6
Turn the MIX encoder to adjust the signal level
that is sent to the STEREO bus.
Hint
You can also switch the output to the STEREO bus on/off and
adjust the pan from within the MATRIX/ST ROUTING screen
(MATRIX/ST function). If desired, the send position (post fader
or post ON key) for the signal sent from the MIX channel to
the STEREO bus can also be changed in this screen
(
➥
p.264).
7
In the STEREO A/B channel strip, turn the STE-
REO A [ON] key and STEREO B [ON] key on
(LED lit).
8
In the STEREO A/B channel strip, raise the
[STEREO A]/[STEREO B] faders.
The signal sent from the MIX channel to the STEREO
bus will be sent from STEREO OUT jacks A/B.
The level of the signal output from the STEREO A/B
channels is shown by the [MASTER] meters in the
meter section.
❏ Pairing MIX channels
Adjacent odd-numbered/even-numbered MIX channels
can be paired. If two MIX channels are paired, their
parameters (with the exception of pan and delay) will be
linked.
1
Turn on the [MIX MASTER] key in the MIX
section.
2
Of the desired two adjacent odd-numbered/
even-numbered MIX channels, hold down the
MIX [SEL] key of one, and press the MIX [SEL]
key of the other.
The [PAIR] LED will light, and the MIX channels will
be paired. At this time, the parameters of the channel
whose MIX [SEL] key you pressed first will be copied
to the channel whose MIX [SEL] key you pressed later.
For example if you pressed the keys in the order of
MIX channel 1 → MIX channel 2, the parameters of
MIX channel 1 will be copied to MIX channel 2.
3
To defeat pairing, hold down the MIX [SEL]
key of one of the paired MIX channels and
press the MIX [SEL] key of the other channel.
When MIX channels are paired, the signal flow will
change as follows.
Use the encoders of the MATRIX section to
adjust the send level
STEREO [PAN] encoder
[TO STEREO] key