Yamaha PM5D-RH V2 Music Mixer User Manual


 
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 57
6
Output channel operations
MIX section
The MIX section adjusts the send level of the signals sent from input channels to MIX buses, and adjusts the output level of
the MIX channels.
A [TO ST] LED
This LED will light when the signal sent from the MIX
channel to the STEREO bus is on.
B [TO MTRX] LED
This LED will light when the signal sent from the MIX
channel to the MATRIX bus is on.
C DCA group LEDs
The LED of the DCA group to which this MIX channel
is assigned will light.
D MIX [PAIR] LED
This LED will light if adjacent odd-numbered/even-
numbered MIX channels are paired.
E MIX [ON] key
If the [MIX SEND] key (9) is on, this switches the sig-
nal sent from the input channel to the MIX bus on/off.
If the [MIX MASTER] key (
J) is on, this switches the
MIX channel on/off.
F MIX encoder
If the [MIX SEND] key (9) is on, this adjusts the send
level to the MIX bus. If the [MIX MASTER] key (
J) is
on, this adjusts the output level of the MIX channel.
G MIX [CUE] key
This is used to monitor a MIX channel via the Cue
Monitor/Solo function.
H MIX [SEL] key
This selects the MIX channel to which operations in
the SELECTED CHANNEL section or in the display
will apply.
I [MIX SEND] key
J [MIX MASTER] key
These keys switch the operation of the MIX section.
When the [MIX SEND] key is on, you can use the con-
trols of the MIX section to edit the send level and on/
off status of the signal being sent from the currently
selected input channel to the MIX buses. Controls
other than
46 will have no effect.
When the [MIX MASTER] key is on, you can use the
controls of the MIX section to edit the output level and
on/off status of the MIX channels.
Sending signals from MIX channels to
output jacks
Here’s how a signal sent from an input channel to a MIX
bus can be sent from the corresponding MIX OUT jack.
1
Make sure that an appropriate signal is being
sent from an input channel to the MIX bus.
2
Press the [MIX MASTER] key in the MIX
section.
When this key is on, you can use the MIX section to
control the signals being sent from the MIX channels
to the MIX OUT jacks.
3
Turn on the MIX [ON] key for the MIX chan-
nel whose signal you want to output.
4
Turn the MIX encoder to adjust the output
level of the corresponding MIX channel.
The signal of the corresponding MIX channel will be
sent from the corresponding MIX OUT jack.
5
If you want the meters of the panel to indi-
cate the output level of the MIX channels,
press the [MIX/MATRIX] key of the meter
section.
The output level of the MIX channels will be shown by
the [INPUT/MIX] meters.
Items in the MIX section
9
124
J
7
5
8
6
3
Operations in the MIX section
MIX
PEAK
HOLD
CH 1 -24
24
OVER
-3
-6
-9
-12
-15
-18
-24
-30
-40
-50
-60
OVER
-3
-6
-9
-12
-15
-18
-24
-30
-40
-50
-60
2322212019181716151413121110987654321
ST IN/
/ST IN
MATRIX
INPUT/MIX meters
[MIX/MATRIX] key