Filter
Top Products
Appendices
1006
transmitted by each track whose Status is BTH,
EXT, or EX2. For more information, see “Pan” on
page 419.
Note: If you’ve used the CONTROL ASSIGN
TIMBRE/TRACK switch to select 1–8/9–16,
operating the knobs will transmit panpot data to
control the panning.
Post insert effect pan (CC#08) [Bn, 08, vv]
(vv: value, where 00 is far left, 64 is center, and 127 is
far right)
When the above CC# is assigned to the ASSIGNABLE
PEDAL or as the REALTIME KNOBS 5–8 or as the
vector joystick CC control function, operating that
controller will transmit Post Insert Effect Panpot
messages, and the panning of the sound following the
insert effect will change. When this message is
received, the result will be the same as when the
controller is operated.
• In Program mode and Sampling mode, this
message is transmitted/received on the global
MIDI channel. In Combination, and Sequencer
modes, this message is transmitted/received on the
MIDI channel specified for each insert effect.
• When you set “Pan (CC#8)” (Sequencer 8–5a) in
Sequencer mode, or when you re-select the song or
return to the beginning of the measure in Sequencer
mode, Post Insert Effect Panpot messages will be
transmitted by each track whose Status is BTH,
EXT, or EX2. For more information, see “8–5a: IFX”
on page 515.
Controlling effects
Effect control 1 (CC#12) [Bn, 0C, vv]
Effect control 2 (CC#13) [Bn, 0D, vv]
When the above CC# is assigned to the ASSIGNABLE
PEDAL or as the REALTIME KNOBS 5–8 or as the
vector joystick CC control function, operating that
controller will transmit Effect Control 1/2 messages,
and the specified dynamic modulation will be
controlled. When this message is received, the result
will be the same as when the controller is operated.
Although various types of control change can be
selected as dynamic modulation sources, Effect
Control 1 (CC#12) and 2 (CC#13) are dedicated for
dynamic modulation.
Effect 1 depth (Send 2) (CC#91) [Bn, 5B, vv]
Effect 3 depth (Send 1) (CC#93) [Bn, 5D, vv]
When the above CC# is assigned to the ASSIGNABLE
PEDAL or as the REALTIME KNOBS 5–8 or as the
vector joystick CC control function, operating that
controller will transmit Effect 1 Depth (Send 2) or
Effect 3 Depth (Send 1) messages, and the send level 1
or 2 to the master effects MFX1 or MFX2 will be
controlled respectively. When this message is received,
the result will be the same as when the controller is
operated.
On the corresponding MIDI channels, this will
simultaneously control the timbre/track setting as well
as the setting following the Insert Effect.
• In Combination, and Sequencer modes, the actual
send level of the timbre/track is determined by
multiplying this value with the send 1/2 settings
for each oscillator (Program 8–1f).
• When you adjust “Send 1 (MFX1)” or “Send 2
(MFX2)” (Sequencer 8–1b) in Sequencer mode, or
when you re-select a song or return to the
beginning of the measure in Sequencer mode, Send
1/2 will be transmitted by each track whose Status
is BTH, EXT, or EX2.
Effect 2 depth (IFX1–12 on/off) (CC#92) [Bn, 5C,
vv]
Effect 4 depth (MFX1, 2 on/off) (CC#94) [Bn, 5E,
vv]
Effect 5 depth (TFX1, 2 on/off) (CC#95) [Bn, 5F, vv]
Separately from the effect on/off settings in each
mode, “Effect Global SW” (Global 0–1b) allows you to
turn off insert effects IFX1–12 and master effects MFX1,
2 and total effect TFX1, 2.
If you check “IFX1–12 Off,” “MFX1&2 Off” or
“TFX1&2 Off,” the corresponding message will be
transmitted with vv=0 [00]. If you uncheck these
settings, the corresponding message will be
transmitted with vv=127 [7F]. If you check these
settings, the corresponding effect(s) will be turned off
as a group. If you uncheck these settings, the on/off
settings of each mode will be used. The same applies to
reception. (vv of 00 is off, and 01 or greater is the
original setting.) These messages are
transmitted/received on the global MIDI channel.
(“IFX 1–12 on/off” - “MFX 1, 2 on/off” - “TFX 1, 2
on/off”)
Note: These messages are defined simply for use in
adjusting the effect levels, and may not have the same
function on another instrument connected to the
OASYS.
Using various controllers
Here we will explain typical ways to use the various
controllers. You can choose from MIDI CC#00–CC#119
for “REALTIME KNOBS 5…8” and “vector joystick CC
control.”
Foot controller (CC#04) [Bn, 04, vv]
If the above CC# is assigned as the ASSIGNABLE
PEDAL function, this message will be transmitted
when the controller is operated.
• In Combination and Sequencer modes,
transmission/reception of this message can be
turned on/off independently for each timbre/track
(“Enable Foot Pedal/Switch” Combination/
Sequencer 3–3a).
Ribbon controller (CC#16) [Bn, 10, vv]
This message will be transmitted when the OASYS’s
ribbon controller is operated.
• In Combination and Sequencer modes,
transmission/reception of this message can be
turned on/off independently for each timbre/track
(“Enable Ribbon” Combination/Sequencer 3–1a).