Filter
Top Products
Sampling mode
612
MFX2
MFX2 [000…185]
MFX2 On/Off [Off, On]
Return 2 [000…127]
These parameters specify the effect type for master
effect 2, its on/off status, and the return level from
master effect 2 to the L/R bus. See “MFX1” on
page 611.
Chain
Chain On/Off [Off, On]
On (checked): Chain (series connection) will be
turned on for MFX1 and MFX2.
Chain Direction [MFX1→MFX2, MFX2→MFX1]
Specifies the direction of the connection when MFX1
and MFX2 are chained.
MFX1→MFX2: Connect from MFX1 to MFX2.
MFX2→MFX1: Connect from MFX2 to MFX1.
Chain Level [000…127]
When chain is On, this sets the level at which the
sound is sent from the first master effect to the next
master effect.
9–1b: TFX1, 2
These are the parameters for total effect 1 and 2, which
are placed at the final stage of the L/R bus. After
passing through the total effects, the sound is output to
AUDIO OUTPUT (MAIN OUT) L/MONO and R.
For the total effects, the direct sound (Dry) is always
stereo-in/out. The input/output configuration of the
effect sound (Wet) will depend on the selected effect
type.
The total effects are stereo-in and stereo-out, but the
output may be monaural depending on the type of
effect you select.
TFX1
TFX1 [000…185]
This selects the effect type for total effect 1. Choose
from 000:No Effect – 185: Mt.BPM Dly // Mt.BPM Dly.
Category/TFX Select menu
When you press the popup button, the Category/TFX
Select menu will appear, letting you choose effect types
by category. Use the tabs to select an effect category,
and then choose an effect within that category. Press
the OK button to execute your choice, or press the
Cancel button to cancel.
TFX1 On/Off [Off, On]
This turns total effect 1 on/off. If this is off, the input
will be passed directly through. The setting will
alternate between on/off each time you press this.
Separately from this setting, you can use control
change #95 to turn both total effects off. A value of 0
turns them off, and values of 1–127 restore the
original setting. The global MIDI channel specified
by MIDI Channel (Global 1–1a) is used for this
message.
TFX2
TFX2 [000…185]
TFX2 On/Off [Off, On]
These parameters specify the effect type and on/off
status for total effect 2. See “TFX1,” above.
9–1c: Master Volume
Master Volume [000…127]
This specifies the final level of the audio output that
has passed through total effects 1 and 2, and output
from AUDIO OUTPUT (MAIN OUT) L/MONO and R.
Note: You can control the master volume from the
control surface. You can also control this setting from
the P0– Control Surface page.
1. Press the CONTROL ASSIGN MIXER AUDIO
switch to turn it on (lit).
2. Use the MASTER slider to control the level.
▼ 9–1: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see “ENTER + 0-9: shortcuts for menu
commands” on page 138.
• 0: Copy MFX/TFX. For more information, see
“Copy MFX/TFX” on page 153.
• 1: Swap MFX/TFX. For more information, see
“Swap MFX/TFX” on page 154.