Filter
Top Products
Sampling P0: Recording 0–9: Control Surface
581
Knobs 1–8, Channel Strip
When the Mixer Knobs switch is set to Channel Strip,
the knobs provide quick access to the Pan, EQ, and FX
Send parameters. The Pan and EQ parameters
duplicate the similarly-named parameters found on
the Program editing pageS.
PAN [Random, L001…C064…R127]
This controls the stereo pan of the selected Oscillator. A
setting of L001 places the sound at the far left, C064 in
the center, and R127 to the far right.
Random is available only via the LCD. (Otherwise, it
would be difficult to use the knob to sweep smoothly
from left to right.) With the Random setting, the pan
position will be different for each note-on.
EQ TRIM [00…99]
This controls the volume level going into the EQ.
High settings of the Low, Mid, and High Gain controls
can cause substantial increases in the overall level. You
can compensate for this by turning down the input
trim.
Note: if the EQ page EQ Bypass parameter is turned
On, then none of the EQ parameters here will have
any effect.
LOW EQ [–18.0…+00.0…+18.0dB]
This controls the gain of the 80Hz Low Shelf EQ, in
increments of 0.5dB.
MID EQFREQUENCY [100Hz…10kHz]
This sets the center frequency for the Mid sweep EQ.
MID EQ GAIN [–18.0…+00.0…+18.0dB]
This controls the gain of the Mid Sweep EQ, in
increments of 0.5dB.
HIGH EQ [–18.0…+00.0…+18.0dB]
This controls the gain of the 10kHz High Shelf EQ, in
increments of 0.5dB.
SEND 1 [000…127]
This controls the send level into FX Send 1. If the
Program’s Output Bus parameter is set to L/R or OFF,
it scales the Oscillator send levels. If the Output Bus is
set to IFX 1–12, it directly controls the post-IFX send
levels.
SEND 2 [000…127]
This controls the send level into FX Send 2. For more
details, see “SEND 1,” above.
Knobs 1–2, Individual Pan
When the Mixer Knobs switch is set to Individual Pan,
knobs 1 and 2 control the pan settings for Oscillators 1
and 2, respectively. The other 6 knobs have no effect.
These duplicate the Pan parameters of the Oscillators 1
and 2 Amp pages; changing them here will change
them in the editing pages, and vice-versa.
Pan (1) [Random, L001…C064…R127]
This controls the stereo pan of Oscillator 1. A setting of
L001 places the sound at the far left, C064 in the center,
and R127 to the far right.
Random is available only via the LCD. (Otherwise, it
would be difficult to use the knob to sweep smoothly
from left to right.) With the Random setting, the pan
position will be different for each note-on.
Pan (2) [Random, L001…C064…R127]
This controls the stereo pan of Oscillator 2. For more
details, see “Pan (1),”above.
MIX PLAY/MUTE 1
The top row of switches allow you to turn Oscillators 1
on and off, which can be convenient when editing
sounds.
Play/Mute [Off, On]
The oscillator will sound if this switch is on (LED = lit).
When the switch is off (LED = off), Oscillator 1 will be
muted.
Solo switch and MIX SELECT switch 1
Solo [Off, On]
Solo lets you isolate one or more Oscillators or Audio
Inputs, so that you hear them by themselves.
When Solo is Off (LED = Off), the Select switches select
the current Oscillator; when Solo is On (LED = On or
blinking), the Select switches let you solo one or both
Oscillators.
When Solo is On, and one or more Oscillators or Audio
Inputs are soloed, the Solo LED will blink on and off to
remind you that solo is in use.
Clearing all solos
To clear all solos:
1. Press and hold the CONTROLLER RESET button.
2. While holding CONTROLLER RESET, press the
SOLO button.
Note: The main Solo button merely changes the
functions of the Select/Solo switches. It does not
enable or clear the individual solo states.
Exclusive Solo menu parameter
The menu’s Exclusive Solo parameter also affects the
way that Solo works. When Exclusive Solo is Off
(unchecked), you can solo multiple oscillators and
inputs at once.
When Exclusive Solo is On (checked), only one
oscillator or input can be soloed at a time. In this mode,
pressing a Solo switch automatically disables any
previous solos.
You can also toggle Exclusive Solo by holding ENTER
and pressing 1 on the numeric keypad.
OSC Select/Solo [Off, On]
This switch either selects or solos Oscillator, depending
on the Solo switch. For more details, see “Solo,” above.
MIX VOLUMES sliders 1
This adjusts the overall oscillator output level.
OSC Volume [000…127]
This adjusts the oscillator volume level.