Filter
Top Products
MIDI applications Messages transmitted and received by the OASYS
1007
Controller (CC#18) [Bn, 12, vv]
This message will be transmitted when the OASYS’s
VALUE slider is operated.
This is valid in “Program Select” (Program P0: 0–1a)
and “Combination Select” (Combination P0: 0–1a)
when the program or combination number/name is
selected (highlighted).
Knob modulation 5, 6, 7, 8 (CC#17, 19, 20, 21)
[Bn, 11, vv], [Bn, 13, vv], [Bn, 14, vv], [Bn, 15, vv]
If the above CC# are assigned to the REALTIME
KNOBS 5–8, these messages will be transmitted when
the knobs are operated.
• In Combination and Sequencer modes,
transmission/reception of this message can be
turned on/off independently for each timbre/track
(“Enable Realtime Controls Knob 5, 6, 7, 8”
Combination/Sequencer 3–2a).
Vector joystick modulation +X, –X, +Y, –Y
[Bn, 55, vv], [Bn, 56, vv], [Bn, 57, vv], [Bn, 58, vv]
If you assign the above CC#s as the vector joystick CC
control functions, these messages will be transmitted
when you operate the OASYS’ controllers.
They will be transmitted if Global “MIDI Vector
MIDI Out” is set to Vector CC Control.
Controller (CC#83) [Bn, 53, vv]
If you assign the above CC# to a REALTIME KNOBS
5–8 or as the vector joystick CC control function, this
message will be transmitted when you operate the
corresponding controller of the OASYS.
Damper pedal (CC#64) [Bn, 40, vv]
This message is transmitted when you operate a
damper pedal (Korg DS-1H etc.) connected to the
DAMPER jack, and the damper effect will be turned
on/off. If the DS-1H is used, a half-damper effect can
be applied.
• In Combination and Sequencer modes,
transmission/reception of this message can be
turned on/off independently for each timbre/track
(“Enable Damper” Combination/Sequencer 3–1a).
SW1 modulation (CC#80) [Bn, 50, vv]
SW2 modulation (CC#81) [Bn, 51, vv]
If the above CC# are assigned as the function of SW1
or SW2, operating the switch will transmit this
message with vv=127 [7F] for ON, and vv=00 [00] for
OFF.
• In Combination and Sequencer modes,
transmission/reception of these messages can be
turned on/off independently for each timbre/track
(“Enable SW1,” “Enable SW2” Combination/
Sequencer 3–3a)
Foot switch (CC#82) [Bn, 52, vv]
If the above CC# is assigned as the function of the
ASSIGNABLE SWITCH, operating the switch will
transmit this message with vv=127 [7F] for ON, and
vv=00 [00] for OFF.
• In Combination and Sequencer modes,
transmission/reception of this message can be
turned on/off independently for each timbre/track
(“Enable Foot Switch” Combination/Sequencer 3–
3a).
Sostenuto (CC#66) [Bn, 42, vv]
If the above CC# is assigned as the function of the
ASSIGNABLE SWITCH, operating the switch will
transmit this message with vv=127 [7F] for ON, and
vv=00 [00] for OFF, and the sostenuto effect will be
turned on/off. When this message is received, the
result will be the same as when the controller is
operated (OFF for vv=63 [3F] or below, and ON for
vv=64 [40] or above).
Soft pedal (CC#67) [Bn, 43, vv]
If the above CC# is assigned as the function of the
ASSIGNABLE SWITCH, operating the switch will
transmit, and the soft pedal effect will be turned on.
When this message is received, the result will be the
same as when the controller is operated.
When “Foot controller (CC#04)”–“Soft pedal (CC#67)”
are operated on the OASYS, the specified alternate
modulation or dynamic modulation etc. will be
controlled. When these messages are received, the
result will be the same as if the controller had been
operated. For “SW1 modulation (CC#80)”–“Soft pedal
(CC#67),” vv of 63 [3F] or less will be OFF, and 64 [3F]
or greater will be ON.
Controlling Program tone & envelope
shapes
CC#70–79 control specific parameters of a program.
For details on the program parameters that correspond
to each control change, and how the OASYS will
respond in each mode when these are received, refer to
“OASYS and MIDI CCs” on page 995.
Filter cutoff (CC#74) [Bn, 4A, vv]
Resonance level (CC#71) [Bn, 47, vv]
Filter EG intensity (CC#79) [Bn, 4F, vv]
Release time (CC#72) [Bn, 48, vv]
These messages are transmitted when you operate the
OASYS’s REALTIME KNOBS 1–4. (They can also be set
as KNOB 5–8 functions.)
Sustain level (CC#70) [Bn, 46, vv]
Attack time (CC#73) [Bn, 49, vv]
Decay time (CC#75) [Bn, 4B, vv]
LFO 1 speed (CC#76) [Bn, 4C, vv]
LFO 1 depth (pitch) (CC#77) [Bn, 4D, vv]
LFO 1 delay (CC#78) [Bn, 4E, vv]
These messages are transmitted when assign the above
CC# to the REALTIME KNOBS 5–8 or as the vector
joystick CC control function.
When you operate these, the corresponding program
parameters will be controlled, and the sound and
envelope will change. When these messages are
received, the result will be the same as when the
controller is operated. (When the message has a value
vv=64 [40], the setting will have the value that was set
by the program parameter.)
• In Combination and Sequencer modes,
transmission/reception can be turned on/off
independently for each timbre/track (“Enable
Realtime Controls Knob 1…8”
Combination/Sequencer 3–2a).