Filter
Top Products
Dynamic MIDI Sources & Destinations Dynamic MIDI Sources
985
Note: If you want to use the ±X axis of the vector
joystick as a source, set the Global P2–1c: MIDI CC#
Assign-Vector Joystick/Pads parameter “VJS X” to
CC#119.
VJS +X Mod. (CC#85)
The +X direction (the left direction) of the vector
joystick (CC#85) will be the source.
Note: If you want to use the +X axis of the vector
joystick as a source, set the P1–5b: Vector CC Control
parameter “+X” to CC#85 for the desired program,
combination, or song.
VJS -X Mod. (CC#86)
The -X direction (the right direction) of the vector
joystick (CC#86) will be the source.
Note: If you want to use the –X axis of the vector
joystick as a source, set the P1–5b: Vector CC Control
parameter “–X” to CC#86 for the desired program,
combination, or song.
VJS +Y Mod. (CC#87)
The +Y direction (away from yourself) of the vector
joystick (CC#87) will be the source.
Note: If you want to use the +Y axis of the vector
joystick as a source, set the P1–5b: Vector CC Control
parameter “+Y” to CC#87 for the desired program,
combination, or song.
VJS -Y Mod. (CC#88)
The -Y direction (toward from yourself) of the vector
joystick (CC#88) will be the source.
Note: If you want to use the –Y axis of the vector
joystick as a source, set the P1–5b: Vector CC Control
parameter “–Y” to CC#88 for the desired program,
combination, or song.
KARMA On/Off*
The KARMA ON/OFF switch will be the source.
KARMA Latch*
The corresponding KARMA LATCH switch will be the
source.
KARMA Slider 1…8*
The corresponding KARMA SLIDER 1–8 will be the
source.
KARMA SWITCH 1…8*
The KARMA SWITCH 1–8 will be the source.
KARMA Scene 1…9, KARMA Scene-Any
*The KARMA SCENE 1–9 will be the source.
If you choose KARMA Scene-Any, the switch you
operated will be the source.
*Note: If a MIDI control change is assigned in the
Global 2–1: Controller/Scale page, this will be
controlled by reception of the assigned MIDI control
change.
Pad 1…8, Pad-Any (CC110…117, Note Number)
The Pads 1–8 will be the source.
If you choose Pad-Any, the pad you operated will be
the source.
Note: If a MIDI control change or Note Number is
assigned in the Global 2–1: Controller/Scale page, this
will be controlled by reception of the assigned MIDI
control change or Note Number. The default values are
shown.
AfterT
Aftertouch (channel aftertouch) will be the source.
JS X
The X (horizontal) direction of the joystick will be the
source.
For JS X, Polarity (7–7b) allows you to select +/– or
–/+ in addition to the usual + or – operations.
When the controller is moved all the way to the left or
right (or top or bottom), the value will change as
follows. The example shown below is for when Tempo
is selected as the destination. (Original tempo is =100
BPM, “Bottom/Top”: 000/127)
+: Far left (0) → far right (maximum)
100 BPM → 200 BPM
–: Far left (0) → far right (maximum)
100 BPM → 50 BPM
+/–: Far left (minimum) → center (0) → far right
(maximum)
50 BPM → 100 BPM → 200 BPM
–/+: Far left (maximum) → center (0) → far right
(minimum)
200 BPM → 100 BPM → 50 BPM
Note Group:
When using the Note Group Sources, Bottom and
Top (7–7b) refer to MIDI Note Numbers C-1…G9:
000: C-1…012: C0…024: C1…036: C2…
045: C3…060: C4…072: C5…084: C6…
096: C7…108: C8…120: C9…127: G9
Short Note
Use Bottom and Top (7–7b) to specify the range of note
numbers. Only notes within the specified range with a
duration of less than 45 ms between note-on and note-
off will be the source.
Note
Use Bottom and Top (7–7b) to specify the range of note
numbers. Notes within the specified range will be the
source. (☞Short Note)
Note Inside Zone
Notes within the key zone of the KARMA module
(Program 7–1b, Combination 7–1c, Sequencer 7–1c)
will be the source.
Use “Input” to specify the applicable KARMA module.
Note Outside Zone
Notes outside the key zone of the KARMA module
(Program 7–1b, Combination 7–1c, Sequencer 7–1c)
will be the source.