Filter
Top Products
Program P7: KARMA 7–5: GE Real-Time Parameters
111
For details on the individual GE Real-Time parameters,
please see the “KARMA GE guide” on page 893.
MIN (Minimum Value) [–5000…+5000]
This sets the parameter value when the selected
controller is at its minimum point—for instance, when
a slider is at the bottom of its throw. Note that you can
reverse the action of the controller by setting this to be
higher than the MAX value, below.
The available values will depend on the GE Real-Time
parameter.
MAX (Maximum Value) [–5000…+5000]
This sets the parameter value when the selected
controller is at its maximum point—for instance, when
a slider is at the top of its throw.
The available values will depend on the GE Real-Time
parameter.
VALUE [–5000…+5000]
This sets the basic value of the GE parameter, which
corresponds to the center position of the controller. It
must be within the MIN and MAX values.
ASSIGN [---, Slider1…8, Slider (SW)1…8,
SW1…8, DynaMIDI1…8]
Here you can assign the controller for the GE Real-
Time parameter.
By assigning GE Real-Time Parameter to KARMA
Real-Time Controls, they can be controlled in real-time
while you play.
---: No assignment.
Slider1…8: Assign the parameter to KARMA SLIDERS
1-8. The slider will continuously control the “value.”
For example, let’s assume that the “Rhythm Swing%”
parameter of the selected GE is set to a MIN of +0000,
and a MAX of +0100.
• If you set “Value”: +0050, “Assign”: Slider 1, and
Polarity:+
Slider 1 at the center position will produce a value
of +0050. At minimum the value will be +0000, and
at maximum the value will be +0100. Turning the
Slider from center toward the minimum will control
the value from +0050…+0000, and turning it from
center toward the maximum will control the value
from +0050…+0100.
• If you set “Value”: +0080, “Assign”: Slider 1, and
”Polarity”:+
Slider 1 at the center position will produce a value
of +0080. At minimum the value will be +0000, and
at far maximum the value will be +0100. Turning the
slider from center toward the minimum will control
the value from +0080…+0000, and turning it from
center toward the maximum will control the value
from +0080…+0100.
Slider (SW) 1…8: Assign the parameter to KARMA
SLIDER 1–8. The Slider will switch the value between
minimum and maximum only. The minimum to center
range of the Slider is off, and the center to maximum is
on.
• If you set “Value”: +0050, “Assign”: Slider (SW) 1,
and Polarity:+
Turning the slider toward the minimum will
produce a value of +0000. Turning it to center or
maximum will produce a value of +0100.
SW1…8: The parameter will be assigned to switch 1–8.
The minimum is off, and the maximum is on.
Note: the correspondence between the KARMA
SLIDERS, SWITCHES and MIDI control change
messages can be specified in Global P3-1:
Controller/Scale, Controller. For SW1…8 and Slider
(SW) 1…8, a MIDI control change message value of
less than 64 will be “off,” and 64 or greater will be
“on.”
DynaMIDI 1…8: This corresponds to Dynamic MIDI
1…8.
Select this if you wish to control a GE parameter using
the controller selected for Source in Dynamic MIDI (7–
8). (Set the Dynamic MIDI “Destination” to RTParams
Control.)
POLARITY [+, –]
This sets the polarity of the selected controller.
+: In the case of Slider 1-8, moving down from the
center will move the value towards the “Minimum”
setting, and moving up from the center will move
towards the “Maximum” setting. In the case of Slider
(SW) 1-8, the bottom of the slider throw will be
“Minimum,” and the top will be “Maximum.” In the
case of SW1-8, the parameter will be “Maximum”
when the LED is lit.
–: In the case of Slider1-8, moving down from the
center will move the value towards the “Maximum”
setting, and moving up from the center will move
towards the “Minimum” setting. In the case of Slider
(SW) 1-8, the bottom of the slider throw will be
“Maximum,” and the top will be “Minimum.” In the
case of SW1-8, the parameter will be “Maximum”
when the LED is dark.
▼ 7-5: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see “ENTER + 0-9: shortcuts for menu
commands” on page 138.
• 0: Write Program. For more information, see “Write
Program” on page 138.
• 1: Exclusive Solo. For more information, see
“Exclusive Solo” on page 138.
• 2: Copy KARMA Module. For more information,
see “Copy KARMA Module” on page 146.
• 3: Initialize KARMA Module. For more
information, see “Initialize KARMA Module” on
page 147.
• 4: Copy Scene. For more information, see “Copy
Scene” on page 147.
• 5: Swap Scenes. For more information, see “Swap
Scene” on page 147.
• 6: Capture Random Seed. For more information,
see “Capture Random Seed” on page 147.