Filter
Top Products
Appendices
982
Program Down
This decrements the current Program or Combination
number, for hands-free patch changes. For more
information, see “Program Up,” above.
Song Start/Stop
The switch can be used to start/stop the sequencer.
Simultaneously, a MIDI Start or Stop message will be
transmitted.
Song Punch In/Out
If Sequencer P0: Preference “Recording Setup” (0–5a) is
set to Manual Punch In, the switch can be used to
punch-in and punch-out when recording on the
sequencer.
Tap Tempo
This duplicates the function of the front-panel TAP
TEMPO button, for setting the system tempo in real-
time.
KARMA ON/OFF
The foot switch will turn the KARMA function on/off.
KARMA LATCH ON/OFF
The foot switch will turn KARMA LATCH on/off.
KARMA SCENE
The foot switch will cycle through KARMA scenes.
The next scene will be selected each time you press the
foot switch.
JS+Y (CC#01)
The switch will control the effect produced by joystick
movement in the +Y direction (Vertical upward).
JS–Y (CC#02)
The switch will control the effect produced by joystick
movement in the –Y direction (Vertical downward).
Ribbon (CC#16)
The switch duplicates the effect of the ribbon
controller.
Value Slider (CC#18)
The switch will control the effect of the VALUE slider.
RT Knob1–8
The switch duplicates the function of the selected
REALTIME KNOB. When the switch is on, it produces
the same effect as when the knob is rotated fully to the
right; when it is Off, it produces the same effect as
when the knob is rotated fully to the left.
SW1, 2
The footswitch duplicates the function of the selected
front-panel switch.
KARMA RTC Slider1–8
The foot switch will control the effect of the KARMA
CONTROLS (slider).
KARMA RTC SW1–8
The foot switch will control the effect of the KARMA
SWITCHES.
PAD1–8
This lets you trigger any of the Pads from the foot
switch. When playing notes, the footswitch triggers the
pad as if it had been hit at maximum velocity. Note
that this can also be used to select a chord, when Chord
mode is on.
Value Inc
The switch will duplicate the function of the front-
panel Inc button. For more information, see
“Using a footswitch to select Programs” on page 45 of
the Operation Guide.
Value Dec
The switch will duplicate the function of the front-
panel Dec button.
Chord SW
This enables and disables Chord mode. For more
information, see “Using Chord mode” on page 49 of
the Operation Guide.
Foot Pedal Assignments
You can connect a pedal (such as the optional Korg
XVP-10 or EXP-2) to the rear-panel ASSIGNABLE
PEDAL input, and then use it to control a wide variety
of functions, as described below.
This setting is made for the entire OASYS, on the
Global P2–1 Controller page.
A note on MIDI CCs
Some of the assignments include MIDI CCs, which are
transmitted whenever the knob is moved. Note that
the MIDI CCs can still be received even if they are not
assigned to a physical controller.
RT Knobs 5-8 and SW1/2 are special cases, since these
can themselves be assigned to different MIDI CCs. If
the footswitch is assigned to duplicate these controls, it
will also use their CC assignments.
List of Foot Pedal assignments
Off
This setting disables the pedal.
Master Volume
This controls the overall volume, and transmits the
Universal System Exclusive Master Volume message
[F0H, 7FH, nn, 04, 01, vv, mm, F7H]. You can use this to
adjust the volumes of all Tracks or Timbres at the same
time, while preserving their relative balance.
For more information, see the diagram under “Master
Volume Slider” on page 21.