Filter
Top Products
Effect Guide
750
post-IFX2, 3, and 4 signals to set the send levels of
Timbres 2, 3, and 4, and use the Send1 and Send2
parameters for the post-IFX5 signal to set the send
levels of Timbres 5 and 6. For Timbres 7 and 16, the
settings of Send1 (to MFX1) and Send2 (to MFX2) will
be effective. (At this time, the actual send levels use
these Send 1 and 2 values multiplied by the Send1 and
2 settings for Program oscillators 1 and 2.)
“Bus Select DKit” is valid if you’ve selected a drum
track for a Timbre (Combination) or Track (Sequencer).
Fig. 2–2a
If you select DKit, the Bus Select settings for each key
become effective, and each drum instrument sound
will be routed to the corresponding buses. At this time,
the actual send levels use these Send 1 and 2 values,
multiplied by the Send1 and 2 settings for each
DrumKit key.
If a drum kit’s Bus Select is set to L/R or Off, the levels
will be these Send 1 and 2 settings multiplied by the
send levels you specify in Program P8: Routing page
for OSC1 Send1 (to MFX1) and Send2 (to MFX2)
(Program 8–1d), just as in other cases (Oscillator Mode
Single or Double).
If Bus Select is set to IFX1–12, use Send1 and Send2
for the post-IFX signal. If Bus Select is set to 1–8, or
1/2–7/8, the Send 1 and 2 settings will be ignored.
Fig. 2–2b
Sampling mode
You can apply insert effects, master effects, and total
effects to an external audio source from the AUDIO
INPUT 1, 2, 3, 4, or S/P DIF IN jacks, and sample the
result. You can also apply insert effects, master effects,
and total effects to samples assigned to a multisample,
and resample the result.
Use the P0– Audio Input page to make settings for
external audio sources from the AUDIO INPUT 1, 2, 3,
4, or S/P DIF IN jacks.
The Bus Select setting for each jack specifies the bus to
which the external input source will be sent. You can
choose from L/R, IFX1–12, 1–8, 1/2–7/8, or Off. If Bus
Select is set to L/R or Off, use Send1 (to MFX1) and
Send2 (to MFX2) to adjust the send levels to the master
effects. If Bus Select is set to IFX1–12, use the post-IFX
Send1 and Send2 to adjust the send levels to the
master effects.
If you want to apply the master effects to the samples
of a multisample and play or resample the result, use
the P8 - Routing page settings Send1 (to MFX1) and
Send2 (to MFX2) or the P8 - Insert FX page settings
post-IFX1–12 Send1 and Send2 settings to adjust the
send levels to the master effects.
Send1 can be controlled by receiving CC#93, and
Send2 by receiving CC#91. These parameters are
controlled on the global MIDI channel.
Note: You can use the control surface to control Send 1
and 2. For details, see “8–1f: OSC MFX Send” on
page 125.
Audio Input, S/P DIF IN
In Program, Combination, Sequencer, and Disk modes,
external audio sources from the AUDIO INPUT 1, 2, 3,
4, and S/P DIF IN jacks can be processed by insert
effects, master effects, and total effects just as they can
in Sampling mode.
In the P0– Audio Input/Sampling page of each mode,
the Use Global Settings parameter makes settings for
external input from the AUDIO INPUT 1, 2, 3, 4, and
S/P DIF IN jacks.
Set Bus Select to specify the bus to which the external
audio input will be sent. You can select L/R, IFX1–12,
1–8, 1/2–7/8, or Off. If Bus Select (Global P0: 0–3a) is
set to L/R or Off, adjust the send levels to the master
effects using Send1 (to MFX1) and Send2 (to MFX2). If
Bus Select is set to IFX1–12, use the post-IFX Send1
and Send2. If this is set to 1–8 or 1/2–7/8, the signal
will not be sent to the master effects.
In Disk mode, effects will use the settings of the
mode in which you previously were.
Note: You can use the control surface to control Send 1
and 2. For details, see “8–1f: OSC MFX Send” on
page 125.