Filter
Top Products
Modulation and Pitch Shift 074: Rotary Speaker
825
Amount [+/–100]
Sets the modulation amount for controlling the mix
level of the direct sound.
Depth [0…100]
Sets the vibrato depth.
Source [Off…Tempo]
Selects the modulation source that will control vibrato
depth.
Amount [+/–100]
Sets the modulation amount for controlling the vibrato
depth.
Speed [Hz] [0.02…20.00]
Sets the vibrato speed.
Source [Off…Tempo]
Selects the modulation source for controlling the
vibrato speed.
Amount [–20.00…+20.00]
Sets the modulation amount for controlling the vibrato
speed.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see “OUTPUT” on page 764.
074: Rotary Speaker
This effect simulates a rotary speaker, and obtains a
more realistic sound by simulating the rotor in the low
range and the horn in the high range separately. The
effect also simulates the stereo microphone settings.
CONTROL
Mode Switch [Rotate, Stop]
Switches between speaker rotation and stop.
Source [Off…Tempo]
Selects a modulation source for Rotate/Stop.
Mode [Toggle, Moment]
This parameter controls how the modulation source
switches between rotation and stop.
When Mode = Toggle, the speaker rotates or stops
alternately each time you press the pedal or move the
joystick. Via MIDI, rotation will switch between start
and stop each time the modulation amount exceeds 64.
When Mode = Moment, the speaker rotates by default,
and stops only when you press the pedal or move the
joystick. Via MIDI, modulation values above 64 make
the speaker rotate, and values below 64 make it stop.
Speed Switch [Slow, Fast]
Switches the speaker rotation speed between slow and
fast.
Source [Off…Tempo]
Selects a modulation source for Slow/Fast.
Mode [Toggle, Moment]
This parameter controls how the modulation source
switches the rotation speed between slow and fast.
When Mode = Toggle, the speed will switch between
slow and fast each time you press the pedal or move
the joystick. Via MIDI, the speed will switch each time
the modulation amount exceeds 64.
When Mode = Moment (short for Momentary), the
speed is usually slow. It becomes fast only when you
press the pedal or move the joystick. Via MIDI,
modulation values above 64 set the speed to Fast, and
values below 64 set it to Slow.
Manual Speed [Off…Tempo]
This lets you control the rotation speed manually from
a selected modulation source, instead of just switching
between Slow and Fast. If you don’t want to use
manual control, set this to Off.
HORN
Ratio [Stop, 0.50…2.00]
Adjusts the horn rotation speed, which affects the high
frequencies. 1.00 is the default setting. Selecting “Stop”
will stop the rotation.
Acceleration [0…100]
On a real rotary speaker, the rotation accelerates or
decelerates gradually when you switch between slow
and fast, or stop and start. This parameter adjusts how
quickly the Horn speeds up and slows down.
ROTOR
Ratio [Stop, 0.50…2.00]
Adjusts the rotor speed, which affects the low
frequencies. 1.00 is the default setting. Selecting “Stop”
will stop the rotation.
Acceleration [0…100]
This parameter adjusts how quickly the Rotor speeds
up and slows down; see “Acceleration,” above.
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
D
-mod
D
-mod
D
-mod
Mode Switch: Rotate/Stop
Speed Switch: Slow/Fast
Manual Speed Control
Speaker Simulation
Mic Distance
Mic Spread
Horn/Rotor
Balance
Horn
Rotary Speaker
Rotor
+