Filter
Top Products
Effect Guide
832
Tap2 Time [msec] [0.0…1360.0]
Sets the Tap2 delay time.
Feedback (Tap2) [+/–100]
Sets the Tap2 feedback amount.
Source [Off…Tempo]
Selects the modulation source of the Tap2 feedback
amount.
Amount [+/–100]
Sets the modulation amount of the Tap2 feedback
amount.
Tap1 Level [0…100]
This lets you adjust the relative volume of Tap1,
compared to Tap2 (which is always at the maximum
volume). Setting a lower volume for Tap1 can help to
create interesting accent patterns.
High Damp [%] [0…100]
Sets the damping amount in the high range. p.829.
Low Damp [%] [0…100]
Sets the damping amount in the low range. p.829.
Spread [+/–100]
Sets the width of the stereo image of the effect sound.
p.829.
Source [Off…Tempo]
Selects the modulation source of the effect sound’s
stereo image width.
Amount [+/–100]
Sets the modulation amount of the effect sound’s
stereo image width.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see “OUTPUT” on page 764.
082: Stereo Modulation Delay
This stereo delay uses an LFO to sweep the delay time.
The pitch also varies, creating a delay sound which
swells and shimmers. You can also control the delay
time using a modulation source.
CONTROL
Modulation Mode [LFO, Dmod]
Switches between LFO modulation control and
modulation source control.
Dmod Modulation [L/R:+/+, L/R:+/–]
Reversed L/R control by modulation source. p.833.
Source [Off…Tempo]
Selects the modulation source that controls delay time.
Response [0…30]
Sets the rate of response to the modulation source.
LFO
Waveform [Triangle, Sine]
Selects the LFO Waveform.
Shape [-100…+100]
Changes the curvature of the LFO Waveform. p.780.
L LFO Phase [degrees] [–180…+180]
Sets the phase obtained when the left LFO is reset.
p.833.
R LFO Phase [degrees] [–180…+180]
Sets the phase obtained when the right LFO is reset.
p.833.
Dmod Sync [Check-box]
Switches LFO reset off/on. p.833.
Source [Off…Tempo]
Selects the modulation source that resets the LFO.
Frequency [Hz] [0.02…20.00]
This sets the LFO speed, in Hz.
MIDI/Tempo Sync [Check-box]
BPM [MIDI, 40.00…240.00]
Base Note […]
Times [x1…x32]
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see “MIDI/Tempo Sync” on
page 777.
Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO, or one of the Common FX LFOs. For more
information, see “LFO Type” on page 777.
Common LFO Phase Offset [degrees] [+/–180]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
Left
Right
Feedback
LFO Phase
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
LFO: Tri / Sine
Modulation Mode
D-mod
LFO
D
-mod
Delay
Delay
L/R: +/+ +/—
LFO Shape
Response
LFO Sync