Filter
Top Products
Effect Guide
844
Adjust [%] [–2.50…+2.50]
Fine-adjust the left channel delay time.
R Delay Base Note […]
Selects the type of notes to specify the right channel
delay time. p.822.
Times [x1…x32]
Sets the number of notes to specify the right channel
delay time. p.822.
Adjust [%] [–2.50…+2.50]
Fine-adjust the right channel delay time.
L Feedback [+/–100]
Sets the feedback amount for the left channel.
R Feedback [+/–100]
Sets the feedback amount for the right channel.
Source [Off…Tempo]
Selects the modulation source of feedback amount.
L Amount [+/–100]
Sets the modulation amount of the left channel
feedback.
R Amount [+/–100]
Sets the modulation amount of the right channel
feedback.
High Damp [%] [0…100]
Sets the damping amount in the high range. p.829.
Low Damp [%] [0…100]
Sets the damping amount in the low range. p.829.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see “OUTPUT” on page 764.
095: Stereo BPM Multitap Delay
This four-tap delay enables you to select a tempo and
rhythm pattern to set up each tap.
INPUT
Input Level Dmod [%] [+/–100]
Sets the modulation amount of the input level. p.820.
Source [Off…Tempo]
Selects the modulation source for the input level. p.820.
DELAY
BPM [MIDI, 40.00…240.00]
MIDI syncs to the system tempo; 40-240 sets the tempo
manually for this individual effect. p.822.
Time Over?> [---, OVER!]
The maximum delay time is 1,360msec. If the
combination of BPM, Base Note, and Times exceeds
this limit, the error message “OVER!” will appear. If
this occurs, change the delay time parameters so that
this message no longer appears.
Mode [Normal, Cross Feedback,
Cross Pan1, Cross Pan2]
Switches the left and right delay routing. p.831.
Tap 1 Base Note […]
Selects the type of notes to specify the delay time for
Tap1. p.822.
Times [x1…x32]
Sets the number of notes to specify the delay time for
Tap1. p.822.
Tap 2 Base Note […]
Selects the type of notes to specify the delay time for
Tap2. p.822.
Times [x1…x32]
Sets the number of notes to specify the delay time for
Tap2. p.822.
Feedback (Tap2) [+/–100]
Sets the Tap2 feedback amount.
Source [Off…Tempo]
Selects the modulation source of the Tap2 feedback
amount.
Amount [+/–100]
Sets the modulation amount of the Tap2 feedback
amount.
Tap1 Level [0…100]
Sets the Tap1 output level. p.832.
High Damp [%] [0…100]
Sets the damping amount in the high range. p.829.
Low Damp [%] [0…100]
Sets the damping amount in the low range. p.829.
Spread [+/–100]
Sets the width of the stereo image of the effect sound.
p.829.
Tempo
BPM
BPM
Base Note x Times
Base Note x Times
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp
Low Damp
High Damp
Low Damp
Delay
Delay
Feedback
Tap1 Level
Mode
Mode
(1)
(2)
(1)
(2)
Tap1=(1)
Tap2=(2)