Filter
Top Products
Effect Guide
734
Insert Effects (IFX1…IFX12)
In/Out
Insert Effects (IFX 1–12) have a stereo input and a
stereo output. If you set the Wet/Dry parameter (P8–
IFX1–12 page) to Dry (no effect), the input signal will
be passed through, in stereo, without being processed
by the effect. If you select Wet (effect applied), the
processed signal will be output in one of the following
ways:
Mono–Mono Parallel Effects
141: P4EQ // P4EQ - 185: Mt.BPM Dly // Mt.BPM Dly
These effects are typically stereo-in/stereo-out, but
they have a special structure. The L channel and R
channel of the stereo input each have their own
independent mono effect. Each mono output can then
be panned to the desired position in the stereo field.
• Track1: Piano, Pan=L001, Bus Select=IFX1
• Track2: E.Piano, Pan=R127, Bus Select=IFX1
So that you don’t mix the sound of the two tracks that
are being input, set the P0: Play/REC Pan parameter to
L001 and R127 respectively.
Example: IFX1: 148: P4EQ // Phaser
Track 1: Piano is sent to the L channel P4EQ, and Track
2: E.Piano is sent to the R channel Phaser. Use the P8 -
IFX page Pan parameter to set the output position of
each sound. In this example, both are set to C064. See
the diagram below.
If you select 000: No Effect, stereo input signals are
output in stereo without being processed.
Pressing the ON/OFF button of IFX1–IFX12 in the P8:
Insert FX pages in each mode will toggle between ON
and OFF. When OFF is selected, the effect will be
bypassed, and the stereo input signal will be output in
stereo without being processed.
The OASYS can also turn IFX1–IFX12 off separately
from the setting of the ON/OFF button by receiving
MIDI control change message CC#92. Value 0 will
turn them off, and value 1–127 will turn them on.
You can also use “Effect Global SW” to turn IFX1–12
on and off. This MIDI control is performed on the
global MIDI channel.
IFX1: 148: P4EQ // Phaser
Routing
You can use up to twelve channels (IFX 1…12) for the
Insert Effects in any mode.
Program mode
Use Bus Select (Program 8–1c) to set the destination
bus of the oscillator output.
L/R: Send the output to the L/R bus. Instead, it is sent
to AUDIO OUTPUT (MAIN) L/MONO and R after the
TFX1 and 2.
IFX1…12: The signal is sent to Insert Effects IFX 1–12.
1…8, 1/2…7/8: The signal is sent to AUDIO OUTPUT
(INDIVIDUAL) 1…8 bus. For more information, please
see “Individual Outputs” on page 755.
Off: The output will not be sent to the L/R bus, IFX1–
12 buses, or Individual 1–8 buses. Choose the Off
setting if you want to connect the oscillator output to a
master effect in series. Use Send1 (to MFX1) and
Send2 (to MFX2) to adjust the send level.
Use Send1 (to MFX1) and Send2 (to MFX2) (Program
8–1f) to specify the send level for the Master Effects.
This setting is effective if Bus Select (Program 8–1c) is
set to L/R or Off.
Stereo In - Stereo Out
Mono In - Mono Out
Mono In - Stereo Out
Effect
Effect
Effect
+
Effect
+
Wet
Mono In/Out Effect
Mono In/Out Effect
Pan
Pan