Filter
Top Products
Delay 089: Auto Reverse
839
The effect is off when a value for the modulation
source specified for the Reset Source parameter is
63 or smaller, and the effect is on when the value is
64 or higher.
HOLD DELAY: MIDI/Tempo Sync, BPM, Base Note, and
Times
If MIDI/Tempo Sync is on, the Loop Time setting is
ignored; the loop time is determined by BPM, Base
Note, and Times. Even in this case, the delay time
cannot exceed 5,400 msec.
“Hold” procedure (when Loop Time = Auto)
1. REC Source JS +Y: CC#01 Reset Source JS –Y:
CC#02 “Manual Rec Control” Off “Manual Reset
Control” On “Loop Time [msec]” Auto
“MIDI/Tempo Sync” Off
2. It should be noted that all recordings will be
deleted while Reset is On.
3. “Manual Reset Control” Off
Reset is cancelled and the unit enters Rec ready
mode.
4. Push the joystick in the +Y direction (forward) and
play a phrase you wish to hold. When you pull the
joystick to its original position, the recording will
be finished and the phrase you just played will be
held.
Loop Time is automatically set only for the first
recording after resetting. If the time length exceeds
5,400msec, Loop Time will be automatically set to
5,400msec. (If you have set “Loop Time” to 1–
5,400msec, the specified loop time will be used
regardless of the time taken from pushing the joy-
stick forward until it is pulled back. However, the
recording method remains the same. The phrase
being played while the joystick is pushed forward
will be held.
)
5. If you made a mistake during recording, pull the
joystick in the –Y direction (back) to reset. In this
way, the recording will be erased. Repeat step 3.
again.
6. The recorded phrase will be repeated again and
again. You can use this to create an
accompaniment.
7. By pushing the joystick in the +Y direction
(forward), you can also overdub performances
over the phrase that is being held.
089: Auto Reverse
This effect records the input signal and automatically
plays it in reverse (the effect is similar to a tape reverse
sound).
CONTROL
Envelope Select [Dmod, Input]
This selects whether the start and end of recording is
controlled via the modulation source or the input
signal level. After recording is completed, the reverse
playback starts immediately.
Dmod: the input signal will be recorded only when the
value of the specified modulation Source is 64 or
higher.
Input: the input signal will be recorded only when its
level exceeds the Threshold level.
Source [Off…Tempo]
Selects the modulation source that controls recording
when Envelope Select is set to Dmod. See “RECORD:
Envelope Select, Source, and Threshold” on page 813.
Threshold [0…100]
Sets the recording start level when Envelope Select is
set to Input. See “RECORD: Envelope Select, Source,
and Threshold” on page 813.
Response [0…100]
Sets the speed of the response to the end of recording✎
p.813.
REVERSE
Mode [Single, Multi]
When Mode is set to Single, you can set up to
2,640msec for Reverse Time. If recording starts during
the reverse playback, the playback will be interrupted.
When Mode is set to Multi, you can make another
recording during the reverse playback. However, the
maximum Reverse Time is limited to 1,320msec.
If you wish to use this with longer phrases or rhythm
patterns, set Mode to Single. If you don’t need a long
playback time, and want playback and record to
overlap, set Mode to Multi.
Input
D-mod
Envelope Select
D
-mod
Envelope Control
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Auto Reverse
Direct
Mix
Rec/Reverse Play
Control
RecRec
Mode/Reverse Time
Input
Mode = Single
Mode = Multi
Time
Reverse Time Reverse Time
Envelope Select = Input
Reverse Reverse