Filter
Top Products
Effect Guide
846
Times [x1…x32]
Sets the number of notes to specify the right channel
delay time. p.822.
L Depth [0…200]
Sets the depth of the left LFO modulation.
R Depth [0…200]
Sets the depth of the right LFO modulation.
L Feedback [+/–100]
Sets the feedback amount of left delay.
R Feedback [+/–100]
Sets the feedback amount of right delay.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see “OUTPUT” on page 764.
097: St. BPM Auto Panning Dly
This stereo auto panning delay enables you to set the
delay time to match the song tempo.
DELAY
BPM [MIDI, 40.00…240.00]
MIDI syncs to the system tempo; 40-240 sets the tempo
manually for this individual effect. p.822.
Time Over? L > [---, OVER!]
Time Over? R > [---, OVER!]
The maximum delay time is 1,360msec per channel
(left and right). If the channel’s combination of BPM,
Base Note, and Times exceeds this limit, the error
message “OVER!” will appear. If this occurs, change
the delay time parameters so that this message no
longer appears.
L Delay Note […]
Selects the type of notes to specify the left channel
delay time. p.822
Times [x1…x32]
Sets the number of notes to specify the left channel
delay time. p.822.
R Delay Note […]
Selects the type of notes to specify the right channel
delay time. p.822.
Times [x1…x32]
Sets the number of notes to specify the right channel
delay time. p.822.
L Feedback [+/–100]
Sets the feedback amount for the left channel.
R Feedback [+/–100]
Sets the feedback amount for the right channel.
High Damp [%] [0…100]
Sets the damping amount in the high range. p.829.
Low Damp [%] [0…100]
Sets the damping amount in the low range. p.829.
LFO
Waveform [Triangle, Sine]
Selects the LFO Waveform.
Shape [+/–100]
Changes the curvature of the LFO Waveform. p.780.
Phase [degrees] [–180…+180]
Sets the LFO phase difference between the left and
right. p.814.
Frequency [Hz] [0.02…20.00]
This sets the LFO speed, in Hz. It applies only when
MIDI/Tempo Sync, below, is Off.
MIDI/Tempo Sync [Check-box]
BPM [MIDI, 40.00…240.00]
Base Note […]
Times [x1…x32]
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see “MIDI/Tempo Sync” on
page 777.
Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO, or one of the Common FX LFOs. For more
information, see “LFO Type” on page 777.
Common LFO Phase Offset [degrees] [+/–180]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
AUTO PAN
Depth [0…100]
Sets the panning width.
Tempo
BPM
BPM
Base Note x Times
Base Note x Times
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
LFO Phase
LFO Shape
Pan
Pan
LFO: Tri / Sin
Depth
Delay
Delay
High DampLow Damp
High Damp
Low Damp
Feedback