Filter
Top Products
Combination P0: Play 0–9: Control Surface
335
Resetting the Vector Joystick
To reset the Vector Joystick to the center position, hold
down RESET CONTROLS and then move the Vector
Joystick.
Resetting KARMA Module parameters
You can also reset all of the sliders and switches in the
KARMA Module, by holding RESET CONTROLS
and then pressing the KARMA MODULE CONTROL
button. Similarly, to reset a single KARMA Scene, hold
RESET CONTROLS and press any of the SCENE
buttons.
0–9a: Combi Select & Tempo
This section duplicates the most important information
from the main Play page.
Bank [INT A–E, USER A–G]
This is the Bank of the current Combi.
Combi [000–127]
This is the current Combi.
(Tempo) [040.00…240.00, EXT]
This is the tempo for the current Combination, which
applies to tempo-synced LFOs and Wave Sequences,
the Vector EG, EXi Step Sequencers, KARMA, and
tempo-synced effects.
EXT means that the tempo will sync to external MIDI
clocks. For more information, see “Tempo” on
page 323.
040.00…240.00 allow you to set a specific tempo in
BPM, with 1/100 BPM accuracy.
0–9b: Timbre 1–8/9–16
This Control Assign setting lets you adjust the volume,
pan, EQ, and FX send settings for Timbres 1–16.
Mixer Knobs [Channel Strip, Individual Pan]
The Mixer Knobs switch is on the front panel,
immediately to the right of the knobs, and is also
duplicated in the on-screen display. The eight knobs
can control two different sets of parameters,
depending on the setting of this switch.
Channel Strip: With this setting, the eight knobs will
control the Pan, EQ, and FX Send settings for the
selected Timbre. Use the TIMBRE/TRACK button to
select a group of 8 Timbres (1–8 or 9–16), and then use
the SELECT buttons to choose the specific Timbre.
Individual Pan: With this setting, the knobs will
control the Pan for the current group of Timbres. Knob
1 controls the pan for Timbre 1 (or 9), knob 2 controls
the pan for Timbre 2 (or 10), and so on.
Mixer Knobs switch
Knobs 1–8, Channel Strip
When the Mixer Knobs switch is set to Channel Strip,
the knobs provide quick access to the Pan, EQ, and FX
Send parameters. The Pan and EQ parameters
duplicate the similarly-named parameters found on
the Combi editing pages; changing them here will
change them in the editing pages, and vice-versa.
Pan [Random, L001…C064…R127]
This controls the stereo pan of the selected Timbre. A
setting of L001 places the sound at the far left, C064 in
the center, and R127 to the far right.
Random is available only via the LCD. (Otherwise, it
would be difficult to use the knob to sweep smoothly
from left to right.) With the Random setting, each note
will have a different, random pan position.
Note: With some EXi instruments, such as the CX-3,
notes cannot be panned individually. For these EXi,
Random pan will move all sounding notes to a
different pan position at each note-on.
EQ Trim [00…99]
This controls the volume level going into the EQ.
High settings of the Low, Mid, and High Gain controls
can cause substantial increases in the overall level. You
can compensate for this by turning down the input
trim.
Note: if the EQ page EQ Bypass parameter is turned
On, then none of the EQ parameters here will have
any effect.
Low EQ [–18.0…+18.0dB]
This controls the gain of the 80Hz Low Shelf EQ, in
increments of 0.5dB.
Mid EQ Freq [100Hz…10.0kHz]
This sets the center frequency for the Mid sweep EQ.
Mid EQ Gain [–18.0…+18.0dB]
This controls the gain of the Mid Sweep EQ, in
increments of 0.5dB.
High EQ [–18.0…+18.0dB]
This controls the gain of the 10kHz High Shelf EQ, in
increments of 0.5dB.