Filter
Top Products
Delay 096: Stereo BPM Mod. Delay
845
Source [Off…Tempo]
Selects the modulation source of the effect sound’s
stereo image width.
Amount [+/–100]
Sets the modulation amount of the effect sound’s
stereo image width.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see “OUTPUT” on page 764.
096: Stereo BPM Mod. Delay
This is a stereo modulation delay that lets you
synchronize the delay time to the tempo of the song.
CONTROL
Modulation Mode [LFO, Dmod]
Switches between LFO modulation control and
modulation source control.
Dmod Modulation [L/R:+/+, L/R:+/–]
Reversed L/R control by modulation source. p.833.
Source [Off…Tempo]
Selects the modulation source that controls delay time.
Response [0…30]
Sets the rate of response to the modulation source.
LFO
Waveform [Triangle, Sine]
Selects the LFO Waveform.
Shape [+/–100]
Changes the curvature of the LFO Waveform. p.780.
L LFO Phase [degrees] [–180…+180]
Sets the phase obtained when the left LFO is reset.
p.833.
R LFO Phase [degrees] [–180…+180]
Sets the phase obtained when the right LFO is reset.
p.833.
Dmod Sync [Check-box]
Switches LFO reset off/on. p.833.
Source [Off…Tempo]
Selects the modulation source that resets the LFO.
Frequency [Hz] [0.02…20.00]
This sets the LFO speed, in Hz. It applies only when
MIDI/Tempo Sync, below, is Off.
MIDI/Tempo Sync [Check-box]
BPM [MIDI, 40.00…240.00]
Base Note […]
Times [x1…x32]
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see “MIDI/Tempo Sync” on
page 777.
Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO, or one of the Common FX LFOs. For more
information, see “LFO Type” on page 777.
Common LFO Phase Offset [degrees] [+/–180]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
MOD DELAY
BPM [MIDI, 40.00…240.00]
MIDI syncs to the system tempo; 40-240 sets the tempo
manually for this individual effect. p.822.
Time Over? L > [---, OVER!]
Time Over? R> [---, OVER!]
The maximum delay time is 1,000msec per channel
(left and right). If the channel’s combination of BPM,
Base Note, and Times exceeds this limit, the error
message “OVER!” will appear. If this occurs, change
the delay time parameters so that this message no
longer appears.
L Delay Base Note […]
Selects the type of notes to specify the left channel
delay time. p.822.
Times [x1…x32]
Sets the number of notes to specify the left channel
delay time. p.822.
R Delay Base Note […]
Selects the type of notes to specify the right channel
delay time. p.822.
Tempo
BPM
BPM
Base Note x Times
Base Note x Times
Left
Right
Feedback
LFO Phase
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
LFO: Tri / Sine
Modulation Mode
D-mod
LFO
D
-mod
Delay
Delay
L/R: +/+ +/—
LFO Shape
Response
LFO Sync