Filter
Top Products
EXi: MS-20EX
292
AMP [–10.00…+10.00]
Specifies the depth and direction of the modulation
applied to the amp (VCA). This scales the combined
effect of the VOLUME knob and its AMS modulation.
5–1f: EXTERNAL MODULATION 2
Source [Off, MG Tri, MG Pulse, EG 1, EG 1 REV,
EG 2, EG 2 REV, List of AMS Sources]
This selects the modulation source to control the
parameters below. For a list of AMS sources, see “AMS
(Alternate Modulation Source) List” on page 967.
HPF CUTOFF [–10.00…+10.00]
Specifies the depth and direction of the modulation
applied to the high-pass filter (HPF) CUTOFF
FREQUENCY.
LPF CUTOFF [–10.00…+10.00]
Specifies the depth and direction of the modulation
applied to the low-pass filter (LPF) CUTOFF
FREQUENCY.
FM MG/T.EXT [–10.00…+10.00]
Specifies the depth and direction of the modulation
applied to FREQUENCY MODULATION MG/T.EXT.
HPF MG/T.EXT [–10.00…+10.00]
Specifies the depth and direction of the modulation
applied to the high-pass filter CUTOFF FREQUENCY
MODULATION MG/T.EXT.
LPF MG/T.EXT [–10.00…+10.00]
Specifies the depth and direction of the modulation
applied to the low-pass filter CUTOFF FREQUENCY
MODULATION MG/T.EXT.
5-1g: Mixers
MIXER 1
This controls the input volumes for the Patch Panel’s
Mixer 1. For more information, see “MIXER 1” on
page 299.
LEVEL A [–10.00…+10.00]
This sets the level and polarity of the first input.
LEVEL B [–10.00…+10.00]
This sets the level and polarity of the second input.
MIXER 2
This controls the input volumes for the Patch Panel’s
Mixer 1. For more information, see “MIXER 2” on
page 299.
LEVEL A [–10.00…+10.00]
This sets the level and polarity of the first input.
LEVEL B [–10.00…+10.00]
This sets the level and polarity of the second input.
5-1h: Parameter Details
When you touch a knob, a yellow square appears
around it, showing that it has been selected.
This area shows details for the selected knob, including
its parameter group and parameter name, its exact
value, and its AMS assignments.
Individual parameters and AMS
The EXTERNAL MODULATION knobs, BASE
NOTE parameter, and TEMPO SYNC and KEY SYNC
switches are not modulatable.
The rest of the parameters on this page can be
modulated by AMS, as described below.
(Parameter group)
This shows the group of the parameter (such as VCO
MIXER).
(Parameter name) [range depends on parameter]
This shows the name and exact value of the parameter.
You can edit the parameter value with any of the
standard data-entry controls.
AMS [List of AMS Sources]
This selects a modulation source to control the selected
parameter. For a list of AMS sources, see “AMS
(Alternate Modulation Source) List” on page 967.
Intensity [range depends on parameter]
This controls the depth and direction of the AMS
modulation. For more information, see “Intensity” on
page 288.
Int. Mod AMS [List of AMS Sources]
You can modulate the main AMS Intensity from
another AMS source. This selects that source.
Intensity [range depends on parameter]
This controls the depth and direction of the Intensity
Mod AMS. The result is summed with the main AMS
Intensity to produce the final modulation amount.
▼ 5–1: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see “ENTER + 0-9: shortcuts for menu
commands” on page 138.
• 0: Write Program. For more information, see “Write
Program” on page 138.
• 1: Exclusive Solo. For more information, see
“Exclusive Solo” on page 138.